Roland FR-5 用户手册
3. BASS EDIT parameters
V-Accordion
r
49
3. BASS EDIT parameters
The parameters of the BASS EDIT group apply to the Bass section (bass and chord notes) and are saved
to the selected Set. They allow you to build your own (virtual) accordion. After setting these parame-
ters, you probably also need to adjust the TREBLE EDIT or FREE BS EDIT parameters (which are also
saved to the Set). See pages 38 and 40 for how to select and adjust the parameters.
to the selected Set. They allow you to build your own (virtual) accordion. After setting these parame-
ters, you probably also need to adjust the TREBLE EDIT or FREE BS EDIT parameters (which are also
saved to the Set). See pages 38 and 40 for how to select and adjust the parameters.
Press [UP] and [DOWN] simultaneously to select the value that is indicated as “Default setting”. See also “Introduction”
on p. 43 for some general hints.
on p. 43 for some general hints.
All changes you make here apply to the last Bass regis-
ter you selected. So be sure to press the register whose
settings you wish to change before selecting and edit-
ing any of the BASS EDIT parameters. You can, however,
decide to save your settings to a different register (see
below) if you realize that you’ve been editing the wrong
one.
ter you selected. So be sure to press the register whose
settings you wish to change before selecting and edit-
ing any of the BASS EDIT parameters. You can, however,
decide to save your settings to a different register (see
below) if you realize that you’ve been editing the wrong
one.
• When you select another Set
• When you switch off the FR-7/FR-5
Changes you want the FR-7/FR-5 to remember must be
saved as soon as possible. Here is how:
• When you switch off the FR-7/FR-5
Changes you want the FR-7/FR-5 to remember must be
saved as soon as possible. Here is how:
(1) Press and hold the [MENU÷WRITE] button until the
following page appears:
(2) Rotate the [DATA÷ENTER] knob (or use the [UP]/
[DOWN] buttons) to select “Bass”.
(3) Press the [DATA÷ENTER] knob to confirm your
selection.
(4) Use the [DATA÷ENTER] knob or the [UP]/[DOWN]
buttons to specify what you want to save:
(5) Press the [DATA÷ENTER] knob to confirm your
selection.
Depending on what you chose in step (3) above, the
display now looks as follows:
Depending on what you chose in step (3) above, the
display now looks as follows:
(6) Enter a name for the register you are about to
save.
See p. 43 for details. Changing the name is only nec-
essary if you don’t agree with the name that appears
in the display.
See p. 43 for details. Changing the name is only nec-
essary if you don’t agree with the name that appears
in the display.
(7) Press the [MENU÷WRITE] button to jump to the fol-
lowing page:
(8) Use the [DATA÷ENTER] knob or the [UP]/[DOWN]
buttons to select the Set that should contain your
changed version(s).
Change this setting only if you do not want to save
your settings to the current Set.
changed version(s).
Change this setting only if you do not want to save
your settings to the current Set.
(9) (Only for “Current”:)
Press the [DATA÷ENTER] knob to select “REGISTER”,
then turn it to select the number of the register
where you want to save your edited version (1~7).
then turn it to select the number of the register
where you want to save your edited version (1~7).
Important note
Saving your changes
Current: The register you are currently editing.
Currnt +
SCom:
SCom:
ALL
All registers. This is probably the safest
bet, because it ensures that no Bass regis-
ter will be forgotten. (It is perfectly possi-
ble to edit several registers without saving
them.)
bet, because it ensures that no Bass regis-
ter will be forgotten. (It is perfectly possi-
ble to edit several registers without saving
them.)
If you selected “Current” or
“Curnt+SCom”
“Curnt+SCom”
If you selected “ALL”
→ Skip to step (8)
If you selected “Current” or “Curnt+SCom”