Roland FR-5 用户手册
8. ORC FBS EDIT parameters
V-Accordion
r
61
8. ORC FBS EDIT parameters
The parameters of the ORC FBS EDIT group apply to the Bass buttons while Free Bass mode is active.
See page 29 for details about the Orchestra Free Bass section. This section is not available while Bass
mode is active. See pages 38 and 40 for how to select and adjust the parameters.
Press [UP] and [DOWN] simultaneously to select the value that is indicated as “Default setting”.
See page 29 for details about the Orchestra Free Bass section. This section is not available while Bass
mode is active. See pages 38 and 40 for how to select and adjust the parameters.
Press [UP] and [DOWN] simultaneously to select the value that is indicated as “Default setting”.
The selection of Orchestra Free Bass can be automated
using the “2.14 Orchestra Chord Link” parameter
(page 47) – for each Treble register.
using the “2.14 Orchestra Chord Link” parameter
(page 47) – for each Treble register.
• When you select another Set
• When you switch off the FR-7/FR-5
Changes you want the FR-7/FR-5 to remember must be
saved as soon as possible. Here is how:
• When you switch off the FR-7/FR-5
Changes you want the FR-7/FR-5 to remember must be
saved as soon as possible. Here is how:
(1) Press and hold the [MENU÷WRITE] button until the
following page appears:
(2) Rotate the [DATA÷ENTER] knob (or use the [UP]/
[DOWN] buttons) to select “Orc. FreeBs”.
(3) Press the [DATA÷ENTER] knob to confirm your
selection.
(4) Use the [DATA÷ENTER] knob or the [UP]/[DOWN]
buttons to specify what you want to save:
(5) Press the [DATA÷ENTER] knob to confirm your
selection.
Depending on what you chose in step (3) above, the
display now looks as follows:
display now looks as follows:
(6) Use the [DATA÷ENTER] knob or the [UP]/[DOWN]
buttons to select the Set that should contain your
changed version(s).
Change this setting only if you do not want to save
your settings to the current Set.
changed version(s).
Change this setting only if you do not want to save
your settings to the current Set.
(7) Press the [MENU÷WRITE] button to save your
changes. The display briefly shows a confirmation:
(8) Press the [EXIT÷JUMP] button to return to the Main
page.
Note: See pages 38 and 40 for how to select and adjust the
parameters below.
parameters below.
(Off, –40~“Std”~40, Default set-
ting: Std) This parameter allows
you to create the desired “mix”
(volume balance) between the
Orchestra Free Bass section and
the other active sections.
ting: Std) This parameter allows
you to create the desired “mix”
(volume balance) between the
Orchestra Free Bass section and
the other active sections.
This is a relative parameter, which means that its value
is added to or subtracted from the standard value
(“Std”).
is added to or subtracted from the standard value
(“Std”).
(0~127 for all three) Use these
parameters to set the Reverb, Chorus
or Delay send level (how much effect
should be applied to the Orchestra
Free Bass section). The higher the
value you set, the more the Orchestra
section will be processed by the effect
in question.
parameters to set the Reverb, Chorus
or Delay send level (how much effect
should be applied to the Orchestra
Free Bass section). The higher the
value you set, the more the Orchestra
section will be processed by the effect
in question.
The other sections (Bass, Free Bass,
etc.) have the same parameters, so
that you can create a sound image with various “levels”
(foreground, background).
etc.) have the same parameters, so
that you can create a sound image with various “levels”
(foreground, background).
Important note
Saving your changes
Current: The register you are currently editing.
Currnt +
SCom:
SCom:
ALL
All registers. This is probably the safest
bet, because it ensures that no Orchestra
Free Bass register will be forgotten. (It is
perfectly possible to edit several registers
without saving them.)
bet, because it ensures that no Orchestra
Free Bass register will be forgotten. (It is
perfectly possible to edit several registers
without saving them.)
If you selected “Current” or
“Curnt+SCom”
“Curnt+SCom”
If you selected “ALL”
(You cannot select a different register,
or change the name of the current
one.)
or change the name of the current
one.)