Roland JUNO-G 用户手册
169
Connecting to Your Computer via USB
Driver Installation and Settings
In order to use the JUNO-G as a USB MIDI device from your
computer, you must first install the USB MIDI driver. The USB MIDI
driver is on the included “JUNO-G Editor CD” CD-ROM.
computer, you must first install the USB MIDI driver. The USB MIDI
driver is on the included “JUNO-G Editor CD” CD-ROM.
In order to use USB in MIDI mode, you must install the driver from
the included CD-ROM into your computer.
The correct driver and the installation procedure will depend on
your system and on the other programs you are using. Be sure to
read the Readme file on the CD-ROM before installation.
your system and on the other programs you are using. Be sure to
read the Readme file on the CD-ROM before installation.
Windows XP/2000
\Win2kXP\Readme_E.htm
Mac OS X
\JUNO-G Driver OS X\Readme_E.htm
To install the included SONAR LE sequencing software for
Windows XP/2000 into your computer, follow the instructions given
in “To install SONAR LE” in the SONAR LE package.
Windows XP/2000 into your computer, follow the instructions given
in “To install SONAR LE” in the SONAR LE package.
You must perform the following steps before using SONAR LE.
*
Make sure that the included USB MIDI driver is installed. This is not
necessary if you’re using MIDI cables to connect the JUNO-G to your
computer.
necessary if you’re using MIDI cables to connect the JUNO-G to your
computer.
1.
Power up your computer and start up Windows.
2.
Power up the JUNO-G, and switch the JUNO-G to MIDI
3.
Use a USB cable to connect the JUNO-G to your computer.
*
If you’re using MIDI cables to connect the JUNO-G to your
computer, there’s no need to switch the JUNO-G to MIDI mode in
step 2. In this case, use MIDI cables to connect the JUNO-G’s rear
panel MIDI connectors to the MIDI interface that’s connected to your
computer.
computer, there’s no need to switch the JUNO-G to MIDI mode in
step 2. In this case, use MIDI cables to connect the JUNO-G’s rear
panel MIDI connectors to the MIDI interface that’s connected to your
computer.
4.
Start up SONAR LE.
Make MIDI device settings as described in SONAR LE’s Help.
Exchanging MIDI Messages
with Your Computer
(MIDI Mode)
with Your Computer
(MIDI Mode)
Before Installing the Driver
You must set the USB Mode of the JUNO-G to “MIDI mode.” (p. 167)
Caution when disconnecting the
USB cable
USB cable
You must shut down your computer before disconnecting the
USB cable. Disconnecting the cable while your computer’s
power is on may destabilize its operation.
USB cable. Disconnecting the cable while your computer’s
power is on may destabilize its operation.
Using the Included SONAR LE
What is the USB MIDI Driver?
The USB MIDI Driver is a software which passes data between
the JUNO-G and the application (sequencer software, etc.) that
is running on the USB-connected computer.
The USB MIDI Driver sends data from the application to the
JUNO-G, and passes data from the JUNO-G to the application.
the JUNO-G and the application (sequencer software, etc.) that
is running on the USB-connected computer.
The USB MIDI Driver sends data from the application to the
JUNO-G, and passes data from the JUNO-G to the application.
fig.Driver.e
Application
USB
Driver
Computer
USB connector
USB cable
USB connector
JUNO-G
JUNO-G_e.book 169 ページ ２００６年２月１３日 月曜日 午後２時４４分