Roland JUNO-G 用户手册

 

You can use the force with which keys are played to control the way each Tone is played.

 

fig.TMT-V.e

 

When using the Matrix Control to have different tones played, set the lowest value (Lower) and highest value (Upper) of the value of the 
MIDI message used.

 

Instead of using Velocity, you can also have tones substituted using the Matrix Control. However, the keyboard velocity and the Matrix 
Control cannot be used simultaneously to make different tones to sound. When using the Matrix Control to switch tones, set the Tone Mix 
Velo Control parameter to “OFF.”

 

Tone Mix Velo Con-
trol

OFF, ON, 
RANDOM, 
CYCLE

Determines whether a different tone is played (ON) or not (OFF) depending on the force with which the key is played 
(velocity).

 

 The patch’s constituent tones will sound randomly, regardless of any Velocity messages.

 

 The patch’s constituent tones will sound consecutively, regardless of any Velocity messages.

Control Switch

OFF, ON

Velo Fade Lower

0–127

Determines what will happen to the tone’s level when the tone is played at a velocity lower than Velo Range Lower.

If you don’t want the tone to sound at all, set this parameter to “0.”

Velo Range Lower

1–(Upper)

Specifies the lowest velocity at which the tone will sound.

Velo Range Upper

(Lower)–127

Specifies the highest velocity at which the tone will sound.

Velo Fade Upper

0–127

Determines what will happen to the tone’s level when the tone is played at a velocity greater than Velo Range Upper.

If you don’t want the tone to sound at all, set this parameter to “0.”

 

Wave Group

INT, EXP, 
SAMP

Group for the waveform that is to be the basis of the tone

 

 Waveforms stored in internal

 

 Waveform stored in a Wave Expansion Board (SRX series) installed in EXP slots

 

 Sample waveforms

Wave Bank

PRST, USER, 
CARD

When the Wave Group is SAMP: PRST, USER, CARD
When the Wave Group is MSAM: USER, CARD

Wave No. L (Mono)
Wave No. R

----, 1–1267

Basic waveform for a tone (The upper limit will depend on the wave group.)

When in monaural mode, only the left side (L) is specified. When in stereo, the right side (R) is also specified.
If you want to select a left/right pair of Waves, select the left (L) Wave number, and then hold down [SHIFT] and 
press [F4 (STEREO)] to add a check mark (

 

✔

 

); the right (R) (Wave) will be recalled.

Wave Gain

-6, 0, +6, +12

Gain (amplification) of the waveform

The value changes in 6 dB (decibel) steps—an increase of 6 dB doubles the waveform’s gain.

 

Wave Tempo Sync

OFF, ON

When you wish to synchronize a Phrase Loop to the clock (tempo), set this to “ON.”

 

If a waveform from a wave expansion board is selected for the tone, turning the Wave Tempo Sync parameter “ON” 
will cause pitch-related settings and FXM-related settings to be ignored.
• If a sample is selected for a tone, you must first set the BPM (tempo) parameter of the sample.
• If a sample is selected for a tone, Wave Tempo Sync will require twice the normal number of voices.
• When this parameter is set to “ON,” set the Tone Delay Time parameter (p. 45) to “0.”

Velo Range Lower

Velo Range Upper

Velo Fade Lower

Velo Fade Upper

Level

The tone sounded 
when you play softly

The tone sounded 
when you play strongly

Velocity

JUNO-G_e.book 38 ページ ２００６年２月１３日　月曜日　午後２時４４分