Roland GW-8 用户手册
47
System Settings
Pedal
Assign
Assign
FILL UP
The pedal will trigger a fill-in, and
then the next variation will play
(e.g., from MAIN “1” to “2”).
Once you reach variation “4,”
subsequent presses of the pedal
will not change the variation any
farther.
then the next variation will play
(e.g., from MAIN “1” to “2”).
Once you reach variation “4,”
subsequent presses of the pedal
will not change the variation any
farther.
FILL
DOWN
DOWN
The pedal will trigger a fill-in, and
then the previous variation will play
(e.g., from MAIN “4” to “3”).
Once you reach variation “1,”
subsequent presses of the pedal
will not change the variation any
farther.
then the previous variation will play
(e.g., from MAIN “4” to “3”).
Once you reach variation “1,”
subsequent presses of the pedal
will not change the variation any
farther.
PERFORM
UP
UP
The pedal will switch to the next
Performance (i.e., from PERFORM
001 to 002).
Performance (i.e., from PERFORM
001 to 002).
PERFORM
DOWN
DOWN
The pedal will switch to the
previous Performance (i.e., from
PERFORM 002 to 001).
previous Performance (i.e., from
PERFORM 002 to 001).
FAV
PERFORM
UP
PERFORM
UP
The pedal will switch to the FAVORITE
Performance of the next number or
bank (e.g., from FAVORITE PERFORM
BANK 1-1 to 1-2).
Performance of the next number or
bank (e.g., from FAVORITE PERFORM
BANK 1-1 to 1-2).
FAV
PERFORM
DOWN
PERFORM
DOWN
The pedal will switch to the FAVORITE
Performance of the previous number
or bank (e.g., from FAVORITE
PERFORM BANK 1-2 to 1-1).
Performance of the previous number
or bank (e.g., from FAVORITE
PERFORM BANK 1-2 to 1-1).
FAV
TONE UP
TONE UP
The pedal will switch to the
FAVORITE Tone of the next number
or bank (e.g., from FAVORITE
TONE BANK 1-1 to 1-2).
FAVORITE Tone of the next number
or bank (e.g., from FAVORITE
TONE BANK 1-1 to 1-2).
FAV
TONE
DOWN
TONE
DOWN
The pedal will switch to the
FAVORITE Tone of the previous
number or bank (e.g., from
FAVORITE TONE BANK 1-2 to 1-1).
FAVORITE Tone of the previous
number or bank (e.g., from
FAVORITE TONE BANK 1-2 to 1-1).
Pedal
Polarity
Polarity
STANDARD
,
REVERSE
Switches the polarity of the pedal
connected to the CONTROL PEDAL
jack. Some pedals will operate in
the opposite of the expected way
when you press them. If you’re
using this type of pedal, set this
parameter to “REVERSE.” If you’re
using a Roland pedal (without a
polarity switch), use “STANDARD.”
connected to the CONTROL PEDAL
jack. Some pedals will operate in
the opposite of the expected way
when you press them. If you’re
using this type of pedal, set this
parameter to “REVERSE.” If you’re
using a Roland pedal (without a
polarity switch), use “STANDARD.”
Hold
Polarity
Polarity
STANDARD
,
REVERSE
Switches the polarity of the pedal
connected to the HOLD PEDAL
jack. (See “Pedal Polarity,” above)
connected to the HOLD PEDAL
jack. (See “Pedal Polarity,” above)
SYSTEM D BEAM
Parameter
Value
Explanation
D Beam
Sens
Sens
0–127
This sets the D Beam controller’s
sensitivity. The higher the value set,
the more readily the D Beam
controller goes to into erect.
sensitivity. The higher the value set,
the more readily the D Beam
controller goes to into erect.
D Beam
Assign-
able 1
Type
Assign-
able 1
Type
D Beam
Assign-
able 2
Type
Assign-
able 2
Type
SYSTEM D BEAM SOLO SYNTH
SYSTEM MIDI
Parameter
Value
Explanation
MIDI Tx
Switch
Switch
OFF, ON
Upper Tx
Channel
Channel
1–16
Lower Tx
Channel
Channel
1–16
MIDI Rx
Switch
Switch
OFF, ON
Upper Rx
Channel
1–16
Lower Rx
Channel
1–16
Tx
Tx Pitch
Bend
Bend
OFF, ON
Tx
Modula-
tion
tion
OFF, ON
Tx
Program
Change
OFF, ON
Tx Clock
OFF, ON
Tx Start-
Stop
Stop
OFF, ON
Tx Song
Position
Position
OFF, ON
GW-8_e.book 47 ページ ２００８年４月１日 火曜日 午前１１時４４分