Roland XP-30 用户手册
120
Chapter 4. Memory Settings (Utility/Card Mode)
Specifies the data to be transmitted through the combinations
as shown below.
For example, if you wish to transmit the USER group Patches
001–020, you would specify “PATCH USER:001-020.”
as shown below.
For example, if you wish to transmit the USER group Patches
001–020, you would specify “PATCH USER:001-020.”
Type
Block
ALL
USER
TEMP
TEMP
PERFORM
USER
01–32
TEMP
-PATCH
*1
+PATCH
*2
CTRL
PATCH
USER
001–128
TEMP
RHYTHM
USER
001–002
TEMP
SYSTEM
USER
*1
The current Performance
*2
The current Performance and the Patch or Rhythm Set
assigned to each Part of the Performance
assigned to each Part of the Performance
Type (Data Type)
Specify the type of data to be transmitted.
ALL:
Performance, Patch, and Rhythm Set
PERFORM:
Performance
PATCH:
Patch
RHYTHM:
Rhythm Set
SYSTEM:
System
Block (Source Block)
Specify the source of the data to be transmitted.
USER:
Transmit the data from user memory.
TEMP:
Transmit the data from the temporary area.
CTRL:
Transmit messages for Performance bank select,
Performance program change, and Volume and Pan
messages for the Parts whose Rx parameter
(PERFORM/MIDI/MIDI) is turned ON.
Performance program change, and Volume and Pan
messages for the Parts whose Rx parameter
(PERFORM/MIDI/MIDI) is turned ON.
Destination
Set the transmission destination to MIDI.
■
Transmitting Data to User
Memory
You can transmit Patch, Performance or Rhythm Set settings
to the user memory and System settings to the system
memory. By loading sound data from memory card or Wave
Expansion Boards to user memory, you can add many
different sounds to your performance.
to the user memory and System settings to the system
memory. By loading sound data from memory card or Wave
Expansion Boards to user memory, you can add many
different sounds to your performance.
fig.4-27.e
Specifies the data to be transmitted through the combinations
as shown below.
For example if you wish to transmit only the PR-A group
Patch 001, specify “PATCH PR-A:001-001”
as shown below.
For example if you wish to transmit only the PR-A group
Patch 001, specify “PATCH PR-A:001-001”
* If the specified data will not fit completely into the transmission
destination, as much of the data as will fit will be transmitted,
starting at the first number of the specified transmission
destination.
starting at the first number of the specified transmission
destination.
(Example)
Block
Block
PATCH PR-A:001—005
Destination
User:127
If the above settings are made and transmission is
executed, only the two PR-A group Patches 01 and 02 will
be transmitted to USER group Patches 127 and 128.
executed, only the two PR-A group Patches 01 and 02 will
be transmitted to USER group Patches 127 and 128.
Type
Block
ALL
PR-A
PR-B
PR-B
PERFORM
USER
01–32
PR-A, B
01–32
CARD
**
*1
PATCH
USER
001–128
PR-A–C, GM, PR-E
001–128
XP-A, B
001–255
XP-C
001–256
XP-D, E
001–***
*2
CARD
**
*1
RHYTHM
USER
001–002
PR-A–C, GM, PR-E
001–002
XP-A, C
001–008
XP-D, E
001–***
*2
CARD
**
*1
SYSTEM
Card
**
*1
*1
Specified by file number
*2
Depends on the Wave Expansion Board installed
Type (Data Type)
Specify the type of data to be transmitted.
ALL:
Performance, Patch, and Rhythm Set
PERFORM:
Performance
PATCH:
Patch
RHYTHM:
Rhythm Set
SYSTEM:
System (other than sequencer section)
Data type
Source block
Destination