Roland XP-30 用户手册
144
Quick Reference of Procedures
Selecting Performances Using the Digit
Hold Function
Hold Function
1. Press [SHIFT] + [ENTER] (turn on the Digit Hold
function).
2. Use the numeric keys to specify the number of the one’s
place.
* To turn off the Digit Hold function, press [SHIFT] + [ENTER]
once again.
Modifying a Performance (basic
procedure)
procedure)
1. Make the [EDIT] indicator light.
2. Use the function buttons to select the display group.
3. Use [ ]/[ ] to select the desired display page.
4. Turn off the [EDIT] indicator.
5. Use [PART] (function button) to select the Tone.
6. Use [
]/[
] to select a parameter.
7. Use the VALUE dial, [INC]/[DEC], or the numeric keys
to modify the value.
* If you wish to move to a different parameter group, turn on the
[EDIT] indicator.
Adjusting the Volume of a Part
1. Turn on the [EDIT] indicator.
2. Press [PART] (function button).
3. Use [ ]/[ ] to select the PART SETTING display.
4. Set the Level parameter.
Adjusting the Pan Position of a Part
1. Turn on the [EDIT] indicator.
2. Press [PART] (function button).
3. Use [ ]/[ ] to select the PART SETTING display.
4. Set the Pan parameter.
Modifying a Rhythm Set (basic
procedure)
procedure)
1. Press [PERFORM] + [PATCH].
2. Use [
]/[
] to select Part 10.
3. Use the VALUE dial, [INC]/[DEC], or the numeric keys
to select a Rhythm Set.
4. Make the [EDIT] indicator light.
5. Use the function buttons to select the parameter group.
6. Use [ ]/[ ] to select the desired display page.
7. Use [
]/[
] to select a parameter.
8. Use the keyboard to select a rhythm instrument.
9. Use the VALUE dial, [INC]/[DEC], or the numeric keys
to modify the value.
■
Controller Settings
Changing the Range of the Pitch Bend
Lever (for each Patch)
Lever (for each Patch)
Bend Range parameter (PATCH/CONTROL/KEY
MODE&BENDER)
MODE&BENDER)
Selecting the MIDI Messages
Controlled by the C1–C4 Sliders
Controlled by the C1–C4 Sliders
Assign parameter (SYSTEM/CONTROL/C1–C4 ASSIGN)
Selecting the MIDI Messages
Controlled by the CONTROL PEDAL
Controlled by the CONTROL PEDAL
Polarity parameter (SYSTEM/CONTROL/CONTROL PEDAL)
Reversing the Polarity of CONTROL
PEDAL (when using a pedal of another
manufacturer whose polarity is
reversed)
PEDAL (when using a pedal of another
manufacturer whose polarity is
reversed)
Polarity parameter (SYSTEM/CONTROL/CONTROL PEDAL)
Controlling Patch Parameters with a
Slider or Pedal
Slider or Pedal
You can specify up to three control sources (MIDI messages
used for control). However control source 1 is fixed at
“modulation”. For each control source, you can specify up to
four control destinations (parameters to be controlled).
used for control). However control source 1 is fixed at
“modulation”. For each control source, you can specify up to
four control destinations (parameters to be controlled).
1. Specify the MIDI message to be controlled by each
controller (C1–C4, CONTROL PEDAL) (see above).
2. Select the control source.
Control 2/3 parameter (PATCH/CONTROL/CONTROL
SOURCE)
Control 2/3 parameter (PATCH/CONTROL/CONTROL
SOURCE)
3. Specify the control destination (the parameter to be
controlled).
Destination parameter (PATCH/CONTROL/CONTROL1–3)
* If you do not need to set different control sources for each Patch,
set the Control 2/3 parameters (PPATCH/CONTROL/
CONTROL SOURCE) to “SYS-CTRL1” or “SYS-CTRL2,”
and set the Control 1/2 parameters (SYSTEM/CONTROL/
SYS-CTRL ASSIGN) to the MIDI messages that you wish to
use for control.
CONTROL SOURCE) to “SYS-CTRL1” or “SYS-CTRL2,”
and set the Control 1/2 parameters (SYSTEM/CONTROL/
SYS-CTRL ASSIGN) to the MIDI messages that you wish to
use for control.