Roland 5 用户手册
Europa User Guide
Europa User Guide
Europa User Guide
Europa User Guide
Power up diagnostics and actions
Power up diagnostics and actions
Power up diagnostics and actions
Power up diagnostics and actions
Page 21
13. NVRAM Settings verified
13. NVRAM Settings verified
13. NVRAM Settings verified
13. NVRAM Settings verified
NVRAM Is checked for proper Europa settings. Europa stores all board settings (except patches and
presets) in NVRAM – in the same location as the Roland code’s BANK
NVRAM Is checked for proper Europa settings. Europa stores all board settings (except patches and
presets) in NVRAM – in the same location as the Roland code’s BANK
BANK
BANK
BANK C &
C &
C &
C &
D
D
D
D
of presets. If this NVRAM
region has bad settings, a boot code of E
E
E
E----4
4
4
4
or E
E
E
E----5
5
5
5
is shown (depending upon the exact problem). This
also occurs if the NVRAM region’s checksum is invalid. In either situation, the default Europa board
settings are reloaded.
14. Flash patches and presets are verified
settings are reloaded.
14. Flash patches and presets are verified
14. Flash patches and presets are verified
14. Flash patches and presets are verified
14. Flash patches and presets are verified
All patches and presets stored in flash are verified for valid content. If an invalid patch is found, a boot
code of E
All patches and presets stored in flash are verified for valid content. If an invalid patch is found, a boot
code of E
E
E
E----1
1
1
1
is shown. The bad patch(es) are corrected regardless of the memory protect switch’s position.
If an invalid preset is found, a boot code of E
E
E
E----3
3
3
3
is shown. As with patches, presets are also corrected
regardless of the memory protect switch setting.
At this point, the board has passed all diagnostics and has booted into operational (Europa) mode.
At this point, the board has passed all diagnostics and has booted into operational (Europa) mode.
Power up action functions
Power up action functions
Power up action functions
Power up action functions
Europa has several actions that it can perform on powerup. Each is performed by holding the keys
mentioned below, turning the Jupiter 6’s power on, and holding until no longer required (as
documented):
Europa has several actions that it can perform on powerup. Each is performed by holding the keys
mentioned below, turning the Jupiter 6’s power on, and holding until no longer required (as
documented):
TAPE
TAPE
TAPE
TAPE
Boot to Roland mode. No need to hold the TAPE
TAPE
TAPE
TAPE
button after the board has booted.
Once it has booted, the board is ready for operation. Note that patches created under
Europa will not be usable under Roland code without a manual conversion step
(documented below). Conversely, patches created under Roland code will also need
conversion to Europa. But then again, once the patches have been converted to
Europa, why go back to the Roland code?
Europa will not be usable under Roland code without a manual conversion step
(documented below). Conversely, patches created under Roland code will also need
conversion to Europa. But then again, once the patches have been converted to
Europa, why go back to the Roland code?
WRITE +
WRITE +
WRITE +
WRITE + TAPE
TAPE
TAPE
TAPE
Force firmware transfer mode (FTM) boot. The only reason to use this is if the
operational code image is good but crashes when firmware transfer is attempted, and
standard contact with the Europa Firmware Update Utility does not work. A lit B
operational code image is good but crashes when firmware transfer is attempted, and
standard contact with the Europa Firmware Update Utility does not work. A lit B
B
B
B
LED ,1
1
1
1
LED, and 2
2
2
2----8
8
8
8
blinking indicates a successful boot to FTM. Follow the
instructions in the Europa Firmware Update Utility chapter.
BENDER
BENDER
BENDER
BENDER
Restore factory patches, presets, and default Europa board settings. It reloads the
Roland factory patches and presets to NVRAM, writes a converted version of the
NVRAM to on-chip flash, and loads Europa factory defaults into the board settings.
Be sure to hold BENDER
Roland factory patches and presets to NVRAM, writes a converted version of the
NVRAM to on-chip flash, and loads Europa factory defaults into the board settings.
Be sure to hold BENDER
BENDER
BENDER
BENDER
until boot code E
E
E
E----6
6
6
6
shows up. Once E
E
E
E----6
6
6
6
is displayed,
press a key or button to continue the boot process.
Portamento
Portamento
Portamento
Portamento
Copy NVRAM patches and presets to internal Europa flash and convert to Europa
patch/preset format. This is used to convert recently restored patches and presets
(via tape) over to Europa. One such use would be booting Roland code and loading
patches and presets from cassette. NVRAM Is only used as a copy source and is not
altered. Hold until boot code E
(via tape) over to Europa. One such use would be booting Roland code and loading
patches and presets from cassette. NVRAM Is only used as a copy source and is not
altered. Hold until boot code E
E
E
E----2
2
2
2
is shown. Note that Europa will automatically do
this the first time the chip is installed.
Glissando
Glissando
Glissando
Glissando
Copy flash patch/presets to NVRAM and convert the NVRAM to Roland format.
The only reason to use this feature is to share patches and presets with non-Europa
upgraded Jupiter 6 owners. Note that many preset settings, mostly related to the
arpeggiator, are lost since Roland’s NVRAM preset format doesn’t store Europa
specific settings.
The only reason to use this feature is to share patches and presets with non-Europa
upgraded Jupiter 6 owners. Note that many preset settings, mostly related to the
arpeggiator, are lost since Roland’s NVRAM preset format doesn’t store Europa
specific settings.