Roland Prelude 用户手册
![Roland](https://files.manualsbrain.com/attachments/0f4c16ad543d01443d705a6df0a922f055403287/common/fit/150/50/3f2e1fe174f8814c1395beda0db29618b95ef95d02ed697f721709eb4377/brand_logo.png)
46
System Settings
Pedal
Assign
Assign
FILL UP
The pedal will trigger a fill-in, and
then the next variation will play
(e.g., from MAIN “1” to “2”). Once
you reach variation “4,” subsequent
presses of the pedal will not change
the variation any farther.
then the next variation will play
(e.g., from MAIN “1” to “2”). Once
you reach variation “4,” subsequent
presses of the pedal will not change
the variation any farther.
FILL
DOWN
DOWN
The pedal will trigger a fill-in, and
then the previous variation will play
(e.g., from MAIN “4” to “3”). Once
you reach variation “1,” subsequent
presses of the pedal will not change
the variation any farther.
then the previous variation will play
(e.g., from MAIN “4” to “3”). Once
you reach variation “1,” subsequent
presses of the pedal will not change
the variation any farther.
PERFORM
UP
UP
The pedal will switch to the next
Performance (i.e., from PERFORM
001 to 002).
Performance (i.e., from PERFORM
001 to 002).
PERFORM
DOWN
DOWN
The pedal will switch to the previous
Performance (i.e., from PERFORM
002 to 001).
Performance (i.e., from PERFORM
002 to 001).
Pedal
Polarity
Polarity
STANDARD,
REVERSE
REVERSE
Switches the polarity of the pedal
connected to the CONTROL PEDAL
jack. Some pedals will operate in the
opposite of the expected way when
you press them. If you’re using this
type of pedal, set this parameter to
“REVERSE.” If you’re using a Roland
pedal (without a polarity switch), use
“STANDARD.”
connected to the CONTROL PEDAL
jack. Some pedals will operate in the
opposite of the expected way when
you press them. If you’re using this
type of pedal, set this parameter to
“REVERSE.” If you’re using a Roland
pedal (without a polarity switch), use
“STANDARD.”
Hold
Polarity
Polarity
STANDARD,
REVERSE
REVERSE
Switches the polarity of the pedal
connected to the HOLD PEDAL jack.
(See “Pedal Polarity,” above)
connected to the HOLD PEDAL jack.
(See “Pedal Polarity,” above)
SYSTEM D BEAM
Parameter
Value
Explanation
D Beam
Sens
Sens
0–127
This sets the D Beam controller’s
sensitivity. The higher the value set,
the more readily the D Beam
controller goes to into erect.
sensitivity. The higher the value set,
the more readily the D Beam
controller goes to into erect.
D Beam
Filter/As-
signable 1
Filter/As-
signable 1
D Beam
Volume/
Assign-
able 2
Volume/
Assign-
able 2
SYSTEM MIDI
Parameter
Value
Explanation
MIDI Tx
Switch
Switch
OFF, ON
Upper Tx
Channel
Channel
1–16
Lower Tx
Channel
Channel
1–16
MIDI Rx
Switch
Switch
OFF, ON
Upper Rx
Channel
Channel
1–16
Lower Rx
Channel
Channel
1–16
Tx
Tx Pitch
Bend
Bend
OFF, ON
Tx
Modulation
Modulation
OFF, ON
Tx
Program
Change
Program
Change
OFF, ON
Tx Clock
OFF, ON
Tx Start-
Stop
Stop
OFF, ON
Tx Song
Position
Position
OFF, ON
Rx
Rx Sync
OFF, ON
Rx Pitch
Bend
Bend
OFF, ON
Rx
Modulation
Modulation
OFF, ON
Rx
Program
Change
Program
Change
OFF, ON
SYSTEM METRONOME
Parameter
Value
Explanation
Metronome
Switch*
Switch*
OFF, ON
Metronome
Mode
Mode
ALWAYS,
REC, PLAY
REC, PLAY
Metronome
Level
Level
LOW,
MEDIUM,
HIGH
MEDIUM,
HIGH
Prelude_e.book Page 46 Wednesday, January 14, 2009 2:18 PM