Roland RD-700GX 用户手册

 

●

 

Status

2nd byte

3rd byte

EnH

llH

mmH

n = MIDI channel number:

0H - FH (ch.1 - 16)

mm, ll = Pitch Bend value:

00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

*

Not received when the Rx Bender parameter (EDIT: Part Parameter: Rx Bender) is OFF.

 

■

 

●

 

Status

2nd byte

3rd byte

BnH

78H

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*

When this message is received, all notes currently sounding on the corresponding
channel will be turned off.

 

●

 

Status

2nd byte

3rd byte

BnH

79H

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*

When this message is received, the following controllers will be set to their reset values.

Controller

Reset value

Pitch Bend Change

±0 (center)

Channel Pressure

0 (off)

Modulation

0 (off)

Breath Type

0 (min)

Expression

127 (max)

Hold 1

0 (off)

Sostenuto

0 (off)

Soft

0 (off)

Hold 2

0 (off)

RPN

unset; previously set data will not change

NRPN

unset; previously set data will not change

 

●

 

Status

2nd byte

3rd byte

BnH

7BH

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*

When All Notes Off is received, all notes on the corresponding channel will be turned
off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.

 

●

 

Status

2nd byte

3rd byte

BnH

7CH

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*

The same processing will be carried out as when All Notes Off is received.

 

●

 

Status

2nd byte

3rd byte

BnH

7DH

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*

The same processing will be carried out as when All Notes Off is received. OMNI ON
will not be turned on.

 

●

 

Status

2nd byte

3rd byte

BnH

7EH

mmH

n = MIDI channel number:

0H - FH (ch.1 - 16)

mm = mono number:

00H - 10H (0 - 16)

*

The same processing will be carried out as when All Notes Off is received.

*

The Mono/Poly parameter (Tone Info: Mono/Poly) will change.

 

●

 

Status

2nd byte

3rd byte

BnH

7FH

00H

n = MIDI channel number: 

0H - FH (ch.1 - 16)

*

The same processing will be carried out as when All Notes Off is received.

*

The Mono/Poly parameter (Tone Info: Mono/Poly) will change.

 

■

 

●

 

Status
F8H

*

This message will be received if the Clock Source parameter (EDIT: SYSTEM: Clock
Source) is EXT.

 

●

 

Status
FEH

*

When Active Sensing is received, the unit will begin monitoring the intervals of all
further messages. While monitoring, if the interval between messages exceeds 420 ms,
the same processing will be carried out as when All Sounds Off, All Notes Off and Reset
All Controllers are received, and message interval monitoring will be halted.

 

■

 

Status

Data byte

Status

F0H

iiH, ddH, ......,eeH

F7H

F0H:

System Exclusive Message status

ii = ID number:

an ID number (manufacturer ID) to indicate the manufacturer whose
Exclusive message this is. Roland’s manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standard;
Universal Non-realtime Messages (7EH) and Universal Realtime
Messages (7FH).

dd,...,ee = data:

00H - 7FH (0 - 127)

F7H:

EOX (End Of Exclusive)

Of the System Exclusive messages received by this device, the Universal Non-realtime
messages and the Universal Realtime messages and the Data Request (RQ1) messages and
the Data Set (DT1) messages will be set automatically.

 

●

 

❍

 

Status

Data byte

Status

F0H

7EH, dev, 06H, 01H

F7H

Byte

Explanation

F0H

Exclusive status

7EH

ID number (Universal Non-realtime Message)

dev

Device ID (dev: 10H - 1FH (1 - 32), the initial value is 10H (17))

06H

Sub ID#1 (General Information)

01H

Sub ID#2 (Identity Request)

F7H

EOX (End Of Exclusive)

*

When this message is received, Identity Reply message (p. 8) will be transmitted.

 

❍

 

Status

Data byte

Status

F0H

7EH, 7FH, 09H, 01H

F7H

Byte

Explanation

F0H

Exclusive status

7EH

ID number (Universal Non-realtime Message)

7FH

Device ID (Broadcast)

09H

Sub ID#1 (General MIDI Message)

01H

Sub ID#2 (General MIDI 1 On)

F7H

EOX (End Of Exclusive)

*

Not received when the Rx GM/GM2 System On parameter (EDIT: System: Rx GM/GM2
System ON) is OFF.