Roland G6037008-01 用户手册
E-2
Stereo Headphones
Electric Guitar
Guitar Amp
Digital Audio
Player, etc.
Player, etc.
Footswitch
(BOSS FS-6, etc.)
(BOSS FS-6, etc.)
W
The battery compartment is located on the underside.
Insert the included batteries, taking care to orient them correctly.
Note when connecting the ME-70 to the other devices
Step
Step
1
Step
Step
2
Step
Step
4
Step
Step
3
Step
1
Step
2
Step
4
Step
3
Turn down the
volume all the way
on all equipment!
volume all the way
on all equipment!
Connect the
equipment.
equipment.
Insert the plug
to power up the
ME-70.
to power up the
ME-70.
Switch on the
amp's power last!
amp's power last!
You can mix stereo
audio from AUX IN
with the output.
audio from AUX IN
with the output.
The ME-70 has no built-in amp or speakers. To hear sounds,
you'll need to provide a guitar amplifier, stereo headphones,
or other such equipment.
or other such equipment.
For mono output, connect the cable to just the L/MONO jack.
To send the output from the REC OUT/PHONES jack to a
recorder or the like, use a special cable (PCS-31L; sold separately).
If you use an ordinary guitar cable, only the left-channel audio is
output.
If you use an ordinary guitar cable, only the left-channel audio is
output.
When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under
the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to
orient the unit so no buttons or controls get damaged.
When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over.
the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to
orient the unit so no buttons or controls get damaged.
When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over.
Carefully follow the installation instructions for batteries, and make sure you observe the correct polarity.
Avoid using new batteries together with used ones. In addition, avoid mixing different types of batteries.
Remove the batteries whenever the unit is to remain unused for an extended period of time.
If a battery has leaked, use a soft piece of cloth or paper towel to wipe all remnants of the discharge
from the battery compartment. Then install new batteries. To avoid inflammation of the skin, make sure
that none of the battery discharge gets onto your hands or skin. Exercise the utmost caution so that
none of the discharge gets near your eyes. Immediately rinse the affected area with running water if
any of the discharge has entered the eyes.
Never keep batteries together with metallic objects such as ballpoint pens, necklaces, hairpins, etc.
from the battery compartment. Then install new batteries. To avoid inflammation of the skin, make sure
that none of the battery discharge gets onto your hands or skin. Exercise the utmost caution so that
none of the discharge gets near your eyes. Immediately rinse the affected area with running water if
any of the discharge has entered the eyes.
Never keep batteries together with metallic objects such as ballpoint pens, necklaces, hairpins, etc.
Once the connections have been completed, turn on power to your various devices in
the order specified. By turning on devices in the wrong order, you risk causing malfunction
and/or damage to speakers and other devices.
To prevent malfunction and/or damage to speakers or other devices, always turn down the
volume, and turn off the power on all devices before making any connections.
Raise the amp volume only after turning on the power to all connected devices.
the order specified. By turning on devices in the wrong order, you risk causing malfunction
and/or damage to speakers and other devices.
To prevent malfunction and/or damage to speakers or other devices, always turn down the
volume, and turn off the power on all devices before making any connections.
Raise the amp volume only after turning on the power to all connected devices.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is
required before the unit will operate normally.
When connection cables with resistors are used, the volume level of equipment connected to
the inputs (AUX IN) may be low. If this happens, use connection cables that do not contain resistors.
required before the unit will operate normally.
When connection cables with resistors are used, the volume level of equipment connected to
the inputs (AUX IN) may be low. If this happens, use connection cables that do not contain resistors.
Expected battery life under continuous use: Carbon: 5 hours, Alkaline: 13 hours
These figures will vary depending on the actual conditions of use.
When operating on battery power only, the unit's indicator will become dim when battery power gets too low.
Replace the battery as soon as possible.
We recommend that you keep batteries installed in the unit even when you're powering it with the AC adaptor.
That way, you’ll be able to continue a performance even if the cord of the AC adaptor gets accidently disconnected from the unit.
These figures will vary depending on the actual conditions of use.
When operating on battery power only, the unit's indicator will become dim when battery power gets too low.
Replace the battery as soon as possible.
We recommend that you keep batteries installed in the unit even when you're powering it with the AC adaptor.
That way, you’ll be able to continue a performance even if the cord of the AC adaptor gets accidently disconnected from the unit.
To
un
avo
the
illu
un
avo
the
illu
Creating Sounds
AUX INGUITAR
Making the Connections and Turning the Power On
ME-70_e1.book 2 ページ ２００８年１１月５日 水曜日 午後５時３９分