Yamaha 007POTO-G0 用户手册

下载
页码 290
Top panel
LS9-16/32  Owner’s Manual
21
2
Pa
rts and their function
⁄0
SELECTED CHANNEL section
• • • • • • • • • 
In this section you can operate the most important mix 
parameters for the currently selected input channel or out-
put channel.
The function of the controllers in this section will depend 
on the type of channel that is selected.
1
[HA GAIN] encoder
When an INPUT/ST IN channel is selected
The encoder will adjust the gain of the internal head 
amp or an external head amp device (AD8HR) con-
nected to a rear panel slot.
When any other channel is selected
The encoder will not do anything.
B
[PAN] encoder
When an INPUT/ST IN channel is selected
When a MIX channel is selected
The encoder will adjust the panning of the signal sent 
to the L/R channels (or the L/C/R channels in the case 
of LCR mode) of the STEREO bus. If a MIX channel 
set to stereo is selected, the encoder will adjust the 
output balance of the left and right channels.
When a MATRIX channel is selected
If a monaural MATRIX channel is selected, the 
encoder will not do anything. If a stereo MATRIX 
channel is selected, the encoder will adjust the output 
balance of the left and right channels.
When a STEREO/MONO (C) channel is 
selected
The encoder will not do anything for MONO (C) 
channel. For a STEREO channel, the encoder will 
adjust the output balance of the left and right channels.
C
[SELECTED SEND] encoder
When an INPUT/ST IN channel is selected
The encoder will adjust the send level from that chan-
nel to the currently selected bus. (For a FIXED type 
bus, the encoder will switch the send on/off.)
If the send-destination bus is stereo, this encoder will 
specify the panning of the signal sent to the two buses 
if an odd-numbered bus is selected, or will specify the 
send level if an even-numbered bus is selected.
When a MIX channel is selected
The encoder will adjust the send level from that MIX 
channel to the currently selected MATRIX bus.
When a MATRIX channel is selected
The encoder will adjust the send level from the MIX 
channels to the currently selected MATRIX bus.
D
[DYNAMICS 1] encoder
When an INPUT/ST IN channel is selected
The encoder will adjust the threshold of Dynamics 1 
(e.g., gate).
When any other channel is selected
The encoder will adjust the threshold of the compres-
sor, etc.
E
[DYNAMICS 2] encoder
When an INPUT/ST IN channel is selected
The encoder will adjust the threshold of Dynamics 2 
(e.g., compressor).
When any other channel is selected
The encoder will not do anything.
F
EQ [Q] encoder
G
EQ [FREQUENCY] encoder
H
EQ [GAIN] encoder
These encoders adjust the Q, frequency, and gain of the 
band selected by keys 
9–L.
1
2
4
5
9
J
K
L
3
7
M
8
6
• The PAD will be internally switched on or off when the HA 
gain is adjusted between -14 dB and -13 dB. Keep in mind 
that noise may be generated if there is a difference between 
the Hot and Cold output impedance of the external device 
connected to the INPUT connector when using phantom 
power.
NOTE
• In SENDS ON FADER mode, this encoder will not do any-
thing regardless of which channel is selected.
NOTE
• By simultaneously pressing the EQ [Q] encoder and the EQ 
[GAIN] encoder, you can reset the gain to 0 dB for the band 
selected by the keys below (
9
L
).
• If you have selected a LOW band or HIGH band whose type can 
be changed, you can switch the type by turning the EQ [Q] 
encoder while pressing it when Q is set to the maximum or mini-
mum value.
LOW band :
• Switches to LOW shelving if you turn the encoder toward the 
right while pressing it when Q is at the minimum value
• Switches to high pass filter if you turn the encoder toward the 
left while pressing it when Q is at the maximum value (MIX, 
MATRIX, STEREO, and MONO channels only)
HIGH band :
• Switches to HIGH shelving if you turn the encoder toward the 
right while pressing it when Q is at the minimum value
• Switches to low pass filter if you turn the encoder toward the 
left while pressing it when Q is at the maximum value
For shelving, high pass filter, and low pass filter as well, you can 
switch the type by turning the encoder while pressing it.
HINT