Roland 04672434 用户手册
135
MASTER Chapter 8 Parameter Guide
Chapter 8
CONTROL ASSIGN
Adjust these settings if you would like to use a pedal connected to
the VB-99, or an external MIDI device (control source) to control
parameters as you play.
You can set two parameters as targets to each control source.
the VB-99, or an external MIDI device (control source) to control
parameters as you play.
You can set two parameters as targets to each control source.
*
Turn on the COSM bass, COSM amp, and effect that contains the
parameter you wish to control.
parameter you wish to control.
MASTER
GK VOL (GK Volume)
Parameter/
Range
Range
Explanation
SW
OFF, ON
This setting switches GK VOL on and off.
TARGET PARAMETER
This selects the parameter to be changed.
MIN (Minimum)
This sets the minimum value for the range in which the parameter
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
MAX (Maximum)
This sets the maximum value for the range in which the parameter
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
RANGE LOW, RANGE HIGH
Low: 0–126
High: 1–127
High: 1–127
You can set the controllable range for target
parameters within the GK Volume’s opera-
tional range. Target parameters are con-
trolled within the range set with RANGE
LOW and RANGE HIGH. You should nor-
mally set RANGE LOW to 0 and RANGE
HIGH to 127.
parameters within the GK Volume’s opera-
tional range. Target parameters are con-
trolled within the range set with RANGE
LOW and RANGE HIGH. You should nor-
mally set RANGE LOW to 0 and RANGE
HIGH to 127.
GK S1, S2
(DOWN/S1, UP/S2 Switch)
Parameter/
Range
Range
Explanation
SW
OFF, ON
This setting determines whether control
using DOWN/S1 and UP/S2 is switched on
or off.
using DOWN/S1 and UP/S2 is switched on
or off.
TARGET PARAMETER
This selects the parameter to be changed.
MIN (Minimum)
This sets the minimum value for the range in which the parameter
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
MAX (Maximum)
This sets the maximum value for the range in which the parameter
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
can change.
The value differs depending on the parameter assigned for TARGET
PARAMETER.
MODE
Specify how the value will change in response to an operation.
*
When the DOWN/S1, UP/S2 POS of the GK SETTING is set to
REVRSE position, the function of DOWN/S1, UP/S2 will be
reversed.
REVRSE position, the function of DOWN/S1, UP/S2 will be
reversed.
*
When KEY/BPM/AMPCTL:BPM TAP, FX–DELAY(HOLD)–
REC, or FX–DELAY(HOLD)–STOP is set for the TARGET
PARAMETER, control is available regardless of whether DOWN/S1
or UP/S2 is pressed. In this case, the MODE setting is disabled.
REC, or FX–DELAY(HOLD)–STOP is set for the TARGET
PARAMETER, control is available regardless of whether DOWN/S1
or UP/S2 is pressed. In this case, the MODE setting is disabled.
S1: DEC
S2: INC
S2: INC
S1 will decrease the value, and S2 will in-
crease it.
crease it.
S1: INC
S2: DEC
S2: DEC
S2 will decrease the value, and S1 will in-
crease it.
crease it.
S1: MIN
S2: MAX
S2: MAX
The value will be at MIN when S1 is
pressed.
The value will be at MAX when S2 is
pressed.
pressed.
The value will be at MAX when S2 is
pressed.
S1: MAX
S2: MIN
S2: MIN
The value will be at MAX when S1 is
pressed.
The value will be at MIN when S2 is
pressed.
pressed.
The value will be at MIN when S2 is
pressed.
VB-99_e.book 135 ページ ２００８年８月１８日 月曜日 午後１時１０分