Roland 04672434 用户手册
19
Chapter 1 Outputting Sounds
Chapter 1
other settings can be used fully in two channels.
*
When connecting an expression pedal to the EXP PEDAL jack, set
the pedal’s minimum level knob to the MIN position.
*
When connecting an FS-6 footswitch (optional) to the CTL3/4 jack,
set the MODE switch and POLARITY switch as shown below.
fig.01-010
*
When connecting an FS-5U footswitch (optional) to the CTL3/4
jack, set the POLARITY switch as shown below.
fig.01-020
*
You can connect two FS-5Us using the special Roland PCS-31
connection cable (optional).
*
When an FS-6 is connected to the CTL3,4 jack with an optional
connection cable (stereo 1/4” phone
–
stereo 1/4” phone), pedal
switch B operates according to the CONTROL 3 settings, and pedal
switch A operates according to the CONTROL 4 settings.
fig.01-030
941
Once the connections have been completed (p. 17), turn on power to
your various devices in the order specified. By turning on devices in
the wrong order, you risk causing malfunction and/or damage to
speakers and other devices.
your various devices in the order specified. By turning on devices in
the wrong order, you risk causing malfunction and/or damage to
speakers and other devices.
942
*
This unit is equipped with a protection circuit. A brief interval (a
few seconds) after power up is required before the unit will operate
normally.
943
*
Always make sure to have the volume level turned down before
switching on power. Even with the volume all the way down, you
may still hear some sound when the power is switched on, but this is
normal, and does not indicate a malfunction.
*
Turning on devices in the wrong sequence may result in
malfunction and/or damage to speakers and other devices.
1.
Switch on the POWER switch on the VB-99’s
top panel.
top panel.
The display changes as described below, and after several
seconds the VB-99 is ready for normal performance.
seconds the VB-99 is ready for normal performance.
This screen is called the “Play screen.”
fig.01-060d
Unless special note is made otherwise, the operations
described in this manual are carried out with the Play screen
displayed.
described in this manual are carried out with the Play screen
displayed.
*
When the power to the VB-99 is turned on, the patch selected at the
time the power was last turned off is called up.
985
*
The explanations in this manual include illustrations that depict
what should typically be shown by the display. Note, however, that
your unit may incorporate a newer, enhanced version of the system
(e.g., includes newer sounds), so what you actually see in the display
may not always match what appears in the manual.
2.
Turn on the power to the bass amp or mixer.
*
Raise amp volume levels only after turning on the power to all the
devices.
BOSS FS-6
B
A
BOSS FS-5U
PCS-31 cable
To CTL3,4 jack
To CTL3,4 jack
To CTL3,4 jack
White
Red
White
Red
BOSS
FS-5U
FS-5U
(CTL3)
BOSS
FS-5U
FS-5U
(CTL4)
(CTL3)
(CTL4)
(CTL4)
(CTL3)
• When using the VB-99 with an expression pedal connected
to the EXP PEDAL jack, make the settings described on
“EXP PEDAL (Expression Pedal)”
“EXP PEDAL (Expression Pedal)”
• When using the VB-99 with a footswitch connected to the
CTL3/4 jack, make the settings described on “CTL3, CTL4
(Control3, Control4)”
(Control3, Control4)”
Turning On the Power
VB-99_e.book 19 ページ ２００８年８月１８日 月曜日 午後１時１０分