Roland VB-99 用户手册
114
Chapter 8 Parameters Guide FX (Effects)
PAN
DUAL-S, DUAL-P, DUAL-L/R
WARP
MOD
Parameter/
Range
Range
Explanation
TAP TIME
0%–100%
Adjusts the delay time of the left channel de-
lay. This setting adjusts the L channel delay
time relative to the R channel delay time
(considered as 100%).
lay. This setting adjusts the L channel delay
time relative to the R channel delay time
(considered as 100%).
Parameter/
Range
Range
Explanation
DELAY1 TIME
1 ms–900 ms,
BPM
–BPM
This determines the delay time.
When set to BPM, the value of each parameter will be set according
to the value of the BPM (p. 142) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
to the value of the BPM (p. 142) specified for each patch. This makes
it easier to achieve effect sound settings that match the tempo of the
song.
* If, due to the tempo, the time is longer than the range of allowable
settings, it is then synchronized to a period either 1/2 or 1/4 of that
time.
time.
* After setting DELAY TIME to BPM (
–
), if you tap [F1] (TAP),
the BPM value will change to match the timing of your tapping.
DELAY1 FEEDBACK
0–100
Adjusts the amount of feedback of the Delay1.
A higher value will increase the number of
the delay repeats.
A higher value will increase the number of
the delay repeats.
DELAY HI-CUT (Delay 1 High Cut Filter)
700 Hz–11 kHz, FLAT This sets the frequency at which the high cut
filter of the Delay1 begins to take effect.
When it is set to FLAT, the high cut filter is
off or has no effect.
When it is set to FLAT, the high cut filter is
off or has no effect.
DELAY1 LEVEL
0–120
Adjusts the volume of the Delay1.
DELAY2 TIME
1 ms–900 ms,
BPM
–BPM
This determines the delay time of the
Delay2.
Delay2.
DELAY2 FEEDBACK
0–100
Adjusts the amount of feedback of the
Delay2.
Delay2.
DELAY2 FEEDBACK (Delay 2 High Cut Filter)
700 Hz–11 kHz, FLAT This sets the frequency at which the high cut
filter of the Delay2 begins to take effect.
When it is set to FLAT, the high cut filter is
off or has no effect.
When it is set to FLAT, the high cut filter is
off or has no effect.
DELAY2 LEVEL
0–120
Adjusts the volume of the Delay2.
Parameter/
Range
Range
Explanation
WARP SW
OFF, ON
Turns the WARP effect on/off.
This parameter is assigned to the
footswitch (CTL 3/4) and/or FC-300’s
CTL pedal.
footswitch (CTL 3/4) and/or FC-300’s
CTL pedal.
RISE TIME
0–100
Adjusts how rapidly the warped delay
sound rises.
sound rises.
FB DEPTH (Feedback Depth)
0–100
Adjusts the feedback level of the warped de-
lay sound.
lay sound.
LEVEL DEPTH
0–100
Adjusts the volume of the warped delay
sound.
sound.
Parameter/
Range
Range
Explanation
MOD RATE (Modulation Rate)
0–100
Adjusts the modulation rate of the delay
sound.
sound.
MOD DEPTH (Modulation Depth)
0–100
Adjusts the modulation depth of the delay
sound.
sound.
VB-99_e.book 114 ページ ２００８年８月１８日 月曜日 午後１時１０分