Denon Dj DN-X400 用户手册
9
ENGLISH
6
TRACK MARK
• CD category digital signals are output from the DN-X400’s digital outputs. Track numbers can be added at any
position during recording of these signals onto a digital recorder.
• Connect the DN-X400’s digital outputs to the digital recorder. (Refer to v CONNECTIONS on page 7.)
Start recording on the digital recorder.
Press the TRACK MARK button.
• The output signal’s track number changes
• The output signal’s track number changes
and the green indicator lights for 4 seconds.
1
2
MARK
TRACK
lit
NOTE:
During the 4 seconds in which the track number
is being changed, the track number cannot be
changed again.
During the 4 seconds in which the track number
is being changed, the track number cannot be
changed again.
8
REPLACING THE CROSSFADER
The Crossfader may be removed without any disassembly of the DN-X400 itself.
1. Remove the two A outer screws attaching the crossfader assembly to the front panel.
2. Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.
3. Install the replacement assembly by reversing the above instructions.
2. Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.
3. Install the replacement assembly by reversing the above instructions.
9
SPECIFICATIONS
■ GENERAL
Dimensions:
482 (W) x 105 (H) x 177 (D) mm (without feet)
Installation:
19-inch rack mountable 4U
Mass:
5.5 kg
Power supply:
120 V AC ±10%, 60 Hz (U. S. A. and Canada models)
230 V AC ±10%, 50 Hz (European models)
230 V AC ±10%, 50 Hz (European models)
Power consumption:
26 W
Environmental conditions:
Operational temperature: 5 to 35°C
(41 to 95°F)
Operational humidity:
25 to 85%
(no condensation)
Storage temperature:
-20 to 60°C
(4 to 140°F)
■ AUDIO SECTION
Input Sensitivity & Impedance:
Main Mic
-54 dBV (2.0 mV)
10 k
Ω
/kohms
Aux Mic
-60 dBV (1.0 mV)
10 k
Ω
/kohms
Effect (Return)
-10 dBV (316 mV)
50 k
Ω
/kohms
2-Phono
-50 dBV (3.0 mV)
50 k
Ω
/kohms
8-Line
-14 dBV (200 mV)
50 k
Ω
/kohms
Output level & Impedance:
Main (Balanced)
4 dBm
(1.23 V)
600
Ω
/ohms load
Main (Unbalanced)
0 dBV
(1.0V)
1 k
Ω
/kohms
Booth/Zone (Balanced)
4 dBm
(1.23 V)
600
Ω
/ohms load
Rec (RCA)
-10 dBV (316 mV)
1 k
Ω
/kohms
Effect (Send)
-10 dBV (316 mV)
1 k
Ω
/kohms
Subwoofer
-2 dBV
(800 mV)
1 k
Ω
/kohms
Headphone
-4 dBV
(631 mV)
150
Ω
/ohms (33
Ω
/ohms load)
Frequency Response:
Line
20 to 20 kHz
±2 dB
Phono
20 to 20 kHz
RIAA ±2 dB
Mic
20 to 20 kHz
±2 dB
Signal to Noise ratio:
Line
80 dB
0 dBm, 1 kHz, EQ flat
Phono
75 dB
0 dBm, 1 kHz, EQ flat
Main Mic
65 dB
0 dBm, 1 kHz, EQ flat
Total harmonic distortion rate:
Line
Below 0.05%
Phono
Below 0.05%
Cross talk:
Over 70 dB
Channel equalizer:
Hi
+10 dB, -26 dB (13 kHz)
Mid
+10 dB, -26 dB (1 kHz)
Low
+10 dB, -26 dB (70 Hz)
Microphone equalizer:
Hi
+12 dB, -12 dB (10 kHz)
Mid
+12 dB, -12 dB (1 kHz)
Low
+12 dB, -12 dB (100 Hz)
Digital output (COAXIAL):
Signal format
IEC958 Type
II
Output level
0.5 Vp-p 75
Ω
/ohms
Output signal level
-6 dB
Digital output (OPTICAL):
Signal format
IEC958 Type
II
✽ Specifications and design are subject to change without notice for purpose of improvement.
A
A
7
PFL (Pre Fader Level)
1. Press the HEADPHONE mode button.
2. Press the CUE button that you wish to monitor 1~4 (make sure your source is playing).
3. Turn the blue GAIN level knob until the L/CUE (top) meters peak at the 0 dB level.
4. Perform your mix using the cross fader or channel fader at your desire.
2. Press the CUE button that you wish to monitor 1~4 (make sure your source is playing).
3. Turn the blue GAIN level knob until the L/CUE (top) meters peak at the 0 dB level.
4. Perform your mix using the cross fader or channel fader at your desire.
NOTES:
• For proper operation, your channel levels should always be set to or left on reference line 8.
• This adjustment can be made even if the channel fader is set to zero level.
• For proper operation, your channel levels should always be set to or left on reference line 8.
• This adjustment can be made even if the channel fader is set to zero level.