EarthQuake MODEL 3365PS 用户手册
OPERATOR INSTRUCTIONS ANd PARTS
Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE
Page
GetEarthquake.com
800-45-6007
CONTROLS
dRIvE SAFETY CONTROL LEvER
Engages tines into forward; releasing returns machine to neutral.
Pulling down on the drive safety control lever engages the tines.
Releasing the drive safety control lever disengages the tines to a
neutral position.
Pulling down on the drive safety control lever engages the tines.
Releasing the drive safety control lever disengages the tines to a
neutral position.
BELT TENSION AdjUSTMENT
Proper belt tension is critical to good performance. After 30 minutes
of operation, all cables may have to be adjusted due to initial stretch.
Thereafter, check tension after every two hours of operation.
To increase belt tension:
1. Loosen upper jam nut. Turn nut up cable in 1/8” increments.
2. Tighten lower jam nut.
3. Check adjustment.
This procedure can be repeated until conduit adjustment bolts have
no more adjustment left. If no more adjustment can be made, belt
may have to be replaced.
of operation, all cables may have to be adjusted due to initial stretch.
Thereafter, check tension after every two hours of operation.
To increase belt tension:
1. Loosen upper jam nut. Turn nut up cable in 1/8” increments.
2. Tighten lower jam nut.
3. Check adjustment.
This procedure can be repeated until conduit adjustment bolts have
no more adjustment left. If no more adjustment can be made, belt
may have to be replaced.
dEPTh REGULATOR LEvER
Tilling depth is controlled by the height of the depth regulator lever.
To adjust tilling depth:
1. Remove detent pin.
2. Raise the depth regulator lever to position tines at chosen tilling
To adjust tilling depth:
1. Remove detent pin.
2. Raise the depth regulator lever to position tines at chosen tilling
depth.
3. Align hole in depth regulator lever with hole in depth regulator
bracket and replace detent pin.
ENGINE ShOULd BE OFF BEFORE AdjUSTING
ANY CONTROLS.
dO NOT AdjUST TILLING dEPTh UNLESS dRIvE
SAFETY CONTROL LEvER IS RELEASEd TO ThE
NEUTRAL POSITION.
ANY CONTROLS.
dO NOT AdjUST TILLING dEPTh UNLESS dRIvE
SAFETY CONTROL LEvER IS RELEASEd TO ThE
NEUTRAL POSITION.
WARNING
!
CAUTION
!
ThIS INFORMATION IS PROvIdEd hERE ONLY TO
INTROdUCE ThE CONTROLS. dO NOT START ThE
ENGINE AT ThIS TIME. STARTING ANd OPERATING
INSTRUCTIONS ARE GIvEN ON PAGE 10. PLEASE
REAd ThIS SECTION ANd ALL OPERATING ANd
SAFETY INSTRUCTIONS BEFORE STARTING YOUR
TILLER.
•
INTROdUCE ThE CONTROLS. dO NOT START ThE
ENGINE AT ThIS TIME. STARTING ANd OPERATING
INSTRUCTIONS ARE GIvEN ON PAGE 10. PLEASE
REAd ThIS SECTION ANd ALL OPERATING ANd
SAFETY INSTRUCTIONS BEFORE STARTING YOUR
TILLER.
•
AS A SAFETY PRECAUTION, ThE dRIvE SAFETY
CONTROL LEvER WILL NOT LOCk IN ThE
FORWARd POSITION.
FORWARd POSITION.
•
TO STOP ThE WhEELS ANd TINES AT ANY
TIME, RELEASE ThE dRIvE SAFETY CONTROL
LEvER.
LEvER.
drive safety control lever disengaged
forward cable
upper jam nut
lower jam nut
1/4” stretch
Model 65/65B/65k/65CE handlebar
Model 65PS/65kPS/R65h/65PSCE
handlebar
drive safety control lever disengaged
forward cable
upper jam nut
lower jam nut
1/4” stretch