EarthQuake MODEL 3365K 用户手册

下载
页码 28
Page 10
GetEarthquake.com
800-45-6007
OPERATOR INSTRUCTIONS ANd PARTS 
Front Tine Models 3365_3365B_3365K_3365KPS_3365CE_3365PS_R3355H_3365PSCE
OPERATION
PRE-START INSPECTION
1.  Make sure all safety guards are in place and all nuts and bolts  
are secure.
2.  Check oil level in engine crankcase. See your engine manual for 
procedure and specifications.
3.  Inspect air cleaner for cleanliness. See your engine manual for 
procedure.
4.  Check the fuel supply.  Fill the fuel tank no closer than one inch  
from top of tank to provide space for expansion. See your engine 
manual for fuel recommendations.
5.  Be sure spark plug wire is attached and spark plug is  
tightened securely.
6.  Check position of wheels.
7.  Check depth regulator lever position.
8.  Examine  underneath  and  around  engine  for  signs  of  oil  or  fuel 
leaks.
9.  Inspect fuel hoses for tightness and fuel seepage.
10. Look for signs of engine damage.
11. Remove excessive debris from muffler area and recoil starter.
12. Turn fuel shutoff valve to the ON position if engine is equipped with 
one.  It’s located between tank and carburetor.
START-UP
For models 65, 65B, 65CE, 65k, 65kPS, 
and 65PS only.
The controls required to start and run the rototiller are located on the 
engine and are marked CHOKE and THROTTLE.
A  more  detailed  description  of  engine  operation  and  all  related 
precautions and procedures can be found in the engine manufacturer’s 
manual that accompanies each tiller.
COLd STARTS
1.  Move choke lever to FULL choke position.
2.  Move throttle lever to START.
3.  Pull  starting  rope  out  slowly  one  time  and  allow  to  return 
normally.
4.  Pull starting rope out rapidly and allow rope to return normally.
5.  When engine starts, gradually move choke lever to NO CHOKE 
position and increase throttle speed.
RESTARTING A WARM ENGINE
Restarting an engine that is already warm from previous running does 
not normally require the use of the choke.
1.  Move throttle lever to START position.
2.  Pull  starting  rope  out  rapidly  until  engine  starts.    Allow  rope  to 
return normally. Repeat until engine starts.
3.  Adjust throttle speed to HIgH for best tiller action.
GASOLINE  IS  hIGhLY  FLAMMABLE  ANd  MUST 
BE hANdLEd WITh CARE. NEvER FILL ThE TANk 
WhEN ThE ENGINE IS hOT OR RUNNING. ALWAYS 
MOvE OUTdOORS TO FILL ThE TANk. 
TEMPERATURE OF MUFFLER ANd NEARBY AREAS 
MAY ExCEEd 150° F.  AvOId ThESE AREAS.
dO  NOT  MOvE  ChOkE  CONTROL TO  ChOkE TO 
STOP  ENGINE.  BACkFIRE  OR  ENGINE  dAMAGE 
MAY OCCUR.
TO STOP ThE ENGINE AT ANY TIME, MOvE ThROT-
TLE  CONTROL TO ThE  OFF  POSITION. TO  STOP 
TINES  AT  ANY TIME,  RELEASE  dRIvE  SAFETY 
CONTROL LEvER TO ThE NEUTRAL POSITION.
ALWAYS  RELEASE  dRIvE  SAFETY  CONTROL 
LEvER TO ThE  NEUTRAL  POSITION  BEFORE 
AdjUSTING ThE  dEPTh  OF ThE  REGULATOR 
LEvER.
IMPORTANT
ENGINE IS ShIPPEd FROM FACTORY WIThOUT OIL. 
YOU MUST Add ENGINE OIL BEFORE STARTING 
ENGINE.
PRACTICE  OPERATING ThE  CONTROLS  ANd 
TILLER WITh TINES  OUT  OF  GROUNd  BEFORE 
BEGINNING TO TILL.  IT  IS  IMPORTANT ThAT YOU 
kNOW hOW TO USE ThE TILLER PROPERLY, kEEP 
CONTROL  AT  ALL TIMES,  STOP ThE TINES  ANd 
WhEELS FROM TURNING, ANd STOP ThE ENGINE 
IF  NECESSARY.  IF YOU  dO  NOT  kNOW  hOW TO 
dO ThESE ThINGS,  REAd ThE  CONTROLS  ANd 
SAFETY SECTIONS BEFORE PROCEEdING.
CAUTION
!
WARNING
!
PLEASE dO NOT START YOUR TILLER UNTIL YOU 
hAvE REAd ThE MANUAL ThAT CAME WITh YOUR 
ENGINE  ANd ThE  SECTIONS  IN ThIS  MANUAL 
TITLEd “CONTROLS  ANd  SAFETY.”  ONCE YOU 
hAvE REAd ThESE, FOLLOW ThE APPROPRIATE 
STEPS TO START YOUR TILLER. ALWAYS PERFORM 
ThIS PRE-START ChECkLIST BEFORE STARTING 
ThE ENGINE.