Milwaukee 0201-20 用户手册

POWER TOOL USE AND CARE

16. Do not force the power tool. Use

the correct power tool for your ap-

plication. The correct power tool will

do the job better and safer at the rate

for which it was designed.

17. Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be con-

trolled with the switch is dangerous

and must be repaired.

18. Disconnect the plug from the

power source and/or the battery

pack from the power tool before

making any adjustments, chang-

ing accessories, or storing power

tools. Such preventive safety mea-

sures reduce the risk of starting the

tool accidentally.

19. Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tools or these instructions

to operate power tools. Power

tools are dangerous in the hands of

untrained users.

20. Maintain power tools. Check for

misalignment or binding of mov-

ing parts, breakage of parts and

any other condition that may af-

fect the power tool's operation. If

damaged, have the power tool

repaired before use. Many acci-

dents are caused by poorly maintained

power tools.

21. Keep cutting tools sharp and

clean. Properly maintained cutting

tools with sharp cutting edges are less

likely to bind and are easier to control.

SERVICE

23. Have your power tool serviced by

a qualified repair person using

only identical replacement parts.

This will ensure that the safety of the

power tool is maintained.

WORK AREA SAFETY

ELECTRICAL SAFETY

PERSONAL SAFETY

WARNING!

READ ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, fire

and/or serious injury. The term "power tool" in all of the warnings listed

below refers to your mains-operated (corded) power tool or battery-

opearted (cordless) power tool.

SAVE THESE INSTRUCTIONS

GENERAL SAFETY RULES-FOR ALL POWER TOOLS

1. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

2. Do not operate power tools in ex-

plosive atmospheres, such as in

the presence of flammable liq-

uids, gases, or dust. Power tools

create sparks which may ignite the dust

or fumes.

3. Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose

control.

4. Power tool plugs must match the

outlet. Never modify the plug in any

way. Do not use any adapter plugs

with earthed (grounded) power

tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

5. Avoid body contact with earthed

or grounded surfaces such as

pipes, radiators, ranges and re-

frigerators. There is an increased

risk of electric shock if your body is

earthed or grounded.

6. Do not expose power tools to rain

or wet conditions. Water entering a

power tool will increase the risk of

electric shock.

7. Do not abuse the cord. Never use

the cord for carrying, pulling, or

unplugging the power tool. Keep

cord away from heat, oil, sharp

edges, or moving parts. Damaged

or entangled cords increase the risk of

electric shock.

9. Stay alert, watch what you are do-

ing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the influence of drugs, al-

cohol or medication. A moment of

inattention while operating power tools

may result in serious personal injury.

10. Use safety equipment. Always

wear eye protection. Safety equip-

ment such as dust mask, non-skid

safety shoes, hard hat, or hearing pro-

tection used for appropriate conditions

will reduce personal injuries.

11. Avoid accidental starting. Ensure

the switch is in the off-position

before plugging in. Carrying tools

with your finger on the switch or plug-

ging in power tools that have the

switch on invites accidents.

12. Remove any adjusting key or

wrench before turning the power

tool on. A wrench or a key left at-

tached to a rotating part of the power

tool may result in personal injury.

13. Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the

power tool in unexpected situations.

8. When operating a power tool out-

doors, use an extension cord suit-

able for outdoor use. Use of a cord

suitable for outdoor use reduces the

risk of electric shock.

14. Dress properly. Do not wear loose

clothing or jewellery. Keep your

hair, clothing and gloves away from

moving parts. Loose clothes,

jewellery, or long hair can be caught in

moving parts.

15. If devices are provided for the

connection of dust extraction and

collection facilities, ensure these

are connected and properly used.

Use of these devices can reduce dust-

related hazards.

22. Use the power tool, accessories

and tool bits etc., in accordance

with these instructions and in the

manner intended for the particu-

lar type of power tool, taking into

account the working conditions

and the work to be performed. Use

of the power tool for operations differ-

ent from those intended could result in

a hazardous situation.