Konica Minolta 162 用户手册
When a message appears
8
bizhub 162/210
8-19
SET ORIGINAL TO ADF
A document was not loaded
into the document feeder be-
fore beginning a copy function
(such as, “2in1” copying or
“Mixed orig.” copying) that
uses the document feeder.
Otherwise, the document
feeder is lifted up.
into the document feeder be-
fore beginning a copy function
(such as, “2in1” copying or
“Mixed orig.” copying) that
uses the document feeder.
Otherwise, the document
feeder is lifted up.
Load a document into the
document feeder.
Securely close the document
feeder.
document feeder.
Securely close the document
feeder.
REMOVE PAPER
When interrupting a copy job
to perform a different copy op-
eration other than the “Book
separation” function, the doc-
ument for the interrupted copy
job was left in the document
feeder.
to perform a different copy op-
eration other than the “Book
separation” function, the doc-
ument for the interrupted copy
job was left in the document
feeder.
Remove the document from
the document feeder.
the document feeder.
TEXT/P×1.00
¦[A]§#XXX:EMPTY
(While specifying copy set-
tings)
The selected paper tray has
run out of paper.
“#” indicates the paper tray,
and “XXX” indicates the paper
size.
tings)
The selected paper tray has
run out of paper.
“#” indicates the paper tray,
and “XXX” indicates the paper
size.
Either load paper of the speci-
fied size into the specified pa-
per tray, or press the [Paper]
key and select a different pa-
per size.
fied size into the specified pa-
per tray, or press the [Paper]
key and select a different pa-
per size.
NO SUITABLE PAPER
• While copying, the size of
the paper in the selected
paper tray has changed.
paper tray has changed.
• While copying documents
with mixed sizes using the
auto paper function, paper
of a suitable size could not
be found.
“#” indicates the paper tray,
and “XXX” indicates the pa-
per size.
auto paper function, paper
of a suitable size could not
be found.
“#” indicates the paper tray,
and “XXX” indicates the pa-
per size.
Either load paper of the speci-
fied size, or press the [Paper]
key and select a different pa-
per size.
fied size, or press the [Paper]
key and select a different pa-
per size.
(Flashing alternately)
LOAD PAPER (#XXX)
APS SIZE ERROR
While copying using the auto
paper function, paper of a
suitable size could not be
found.
paper function, paper of a
suitable size could not be
found.
Either load paper of a suitable
size, or press the [Paper] key
and select a different paper
size.
size, or press the [Paper] key
and select a different paper
size.
AMS SIZE ERROR
While copying using the auto
size function, the combination
of the document and paper
sizes caused the zoom ratio to
exceed the range between
×0.5 and ×2.0.
size function, the combination
of the document and paper
sizes caused the zoom ratio to
exceed the range between
×0.5 and ×2.0.
Either load paper of a suitable
size, or use the [
size, or use the [
,] and [+]
keys to specify the zoom ratio.
PAPER SIZE ERROR
The paper loaded in the paper
tray caused a size error.
“#” indicates the paper tray,
and “XXX” indicates the paper
size.
tray caused a size error.
“#” indicates the paper tray,
and “XXX” indicates the paper
size.
Pull open the paper tray with
the size error, and then close it
again.
Check if a custom paper size
has been entered, and correct
the paper size using the ap-
propriate utility mode function.
the size error, and then close it
again.
Check if a custom paper size
has been entered, and correct
the paper size using the ap-
propriate utility mode function.
(Flashing alternately)
RESET PAPER (#XXX)
MEMORY FULL
The size of the data for the
scanned image has exceeded
the capacity of the memory.
scanned image has exceeded
the capacity of the memory.
Press any key, or turn the ma-
chine off, then on again. (The
scanned data should be
cleared from the memory.)
chine off, then on again. (The
scanned data should be
cleared from the memory.)
(Flashing alternately)
PRESS ANY KEY
Message
Cause
Remedy