Samsung CLX-8380ND 用户手册
12.14
<Troubleshooting>
Sensor failure:
[zzz]. Call for
service
[zzz]. Call for
service
There is a problem
in the sensor signal.
in the sensor signal.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
and turn it on again. If
the problem persists,
please call for
service.
Shake [xxx] toner
cartridge
cartridge
The toner supply is
low.
low.
Thoroughly roll the
new cartridge five or
six times to distribute
the toner evenly
inside the cartridge.
(Page 11.3)
new cartridge five or
six times to distribute
the toner evenly
inside the cartridge.
(Page 11.3)
Staple cartridge is
empty. Replace it
empty. Replace it
Stapler is run out.
Staple cartridge is
not installed.
Install it in finisher
not installed.
Install it in finisher
The staple cartridge
is not installed.
is not installed.
Install the staple
cartridge following
the steps explained
on the back of the
finisher door.
(Page 14.2) If you
want to continue the
print job and
disregard of this error
message, go to
Admin Setting to
adjust the option.
(Page 10.2)
cartridge following
the steps explained
on the back of the
finisher door.
(Page 14.2) If you
want to continue the
print job and
disregard of this error
message, go to
Admin Setting to
adjust the option.
(Page 10.2)
System error:
[zzz]. Please turn
off then on
[zzz]. Please turn
off then on
There is a problem
in the system
operation.
in the system
operation.
Turn the machine off
and turn it on again. If
the problem persists,
please call for
service.
and turn it on again. If
the problem persists,
please call for
service.
This IP address
conflicts with an IP
address already in
use. Check it
conflicts with an IP
address already in
use. Check it
The IP address is
used in other place
elsewhere.
used in other place
elsewhere.
Check the IP address
or obtain a new IP
address.
or obtain a new IP
address.
Too much paper in
finisher stacker.
Remove printed
paper
finisher stacker.
Remove printed
paper
The stacker is full of
printouts.
printouts.
Remove printouts
from the stacker.
from the stacker.
Too much paper in
output bin tray.
Remove printed
paper
output bin tray.
Remove printed
paper
The printed papers
are full on the output
tray.
are full on the output
tray.
Remove printed outs
from the output tray.
from the output tray.
Transfer belt is not
valid for this
machine. Check
user? guide
valid for this
machine. Check
user? guide
The transfer belt of
the machine is not for
your machine.
the machine is not for
your machine.
Install the a
Samsung-genuine
part designed for your
machine.
Samsung-genuine
part designed for your
machine.
Transfer belt unit
is worn. Replace it
is worn. Replace it
The life of the
transfer belt expires
totally.
transfer belt expires
totally.
Replace the part with
a new one. Call for
service.
a new one. Call for
service.
Message
Meaning
Suggested solutions
Waste tank is full.
Replace it
Replace it
The life span of the
waste toner
container has
expired and the
printer will stop
printing until a new
waste toner
container is placed
into the printer.
waste toner
container has
expired and the
printer will stop
printing until a new
waste toner
container is placed
into the printer.
USE AUXILIARY
ACCESS
ACCESS
The credit is not
enough to access
the job according to
Foreign Device.
enough to access
the job according to
Foreign Device.
Insert credit into the
Foreign Device.
Foreign Device.
Message
Meaning
Suggested solutions