Xerox 3300MFP 用户手册
2.4
<System setup>
Correcting numbers or names
If you make a mistake while entering a number or name, press the left
Scroll button to delete the last digit or character. Then enter the correct
number or character.
Scroll button to delete the last digit or character. Then enter the correct
number or character.
Inserting a pause
With some telephone systems, you must dial an access code (9, for
example) and listen for a second dial tone. In such cases, you must insert
a pause in the telephone number. You can insert a pause while you are
setting up speed buttons or speed dial numbers.
example) and listen for a second dial tone. In such cases, you must insert
a pause in the telephone number. You can insert a pause while you are
setting up speed buttons or speed dial numbers.
To insert a pause, press Redial/Pause at the appropriate place while
entering the telephone number. A - appears on the display at the
corresponding location.
entering the telephone number. A - appears on the display at the
corresponding location.
Using the save modes
Toner Save mode
Toner Save mode allows your machine to use less toner on each page.
Activating this mode extends the life of the print cartridge beyond what
one would experience in the normal mode, but it reduces print quality.
Activating this mode extends the life of the print cartridge beyond what
one would experience in the normal mode, but it reduces print quality.
To turn this mode on or off, press Toner Saver.
Note
When PC-printing, you can also turn on or off Toner Save mode
in the printer properties. See the Software Section.
in the printer properties. See the Software Section.
Power Save mode
Power Save mode allows your machine to reduce power consumption
when it is not in actual use. You can turn this mode on and select a length
of time for which the machine waits after a job is printed before it switches
to a reduced power state.
when it is not in actual use. You can turn this mode on and select a length
of time for which the machine waits after a job is printed before it switches
to a reduced power state.
1
Press Menu until System Setup appears on the bottom line of the
display and press Enter.
display and press Enter.
2
Press Enter when Machine Setup appears.
3
Press the Scroll buttons until Power Save appears and press
Enter.
Enter.
4
Press the Scroll buttons until On appears and press Enter.
5
Press the Scroll buttons until the time setting you want appears and
press Enter.
press Enter.
6
Press Stop/Clear to return to Standby mode.
Scan Power Save mode
Scan Power Save mode allows you to save power by turning off the scan
lamp. The scan lamp under the scanner glass automatically turns off
when it is not in actual use to reduce power consumption and extend the
life of the lamp. The lamp automatically wakes up after some warm-up
time when you start scanning.
lamp. The scan lamp under the scanner glass automatically turns off
when it is not in actual use to reduce power consumption and extend the
life of the lamp. The lamp automatically wakes up after some warm-up
time when you start scanning.
You can set the length of time for which the scan lamp waits after a scan
job is completed before it switches to the power save mode.
job is completed before it switches to the power save mode.
1
Press Menu until System Setup appears on the bottom line of the
display and press Enter.
display and press Enter.
2
Press Enter when Machine Setup appears.
3
Press the Scroll buttons until Scan PWR Save appears and press
Enter.
Enter.
4
Press the Scroll buttons until the time setting you want appears and
press Enter.
press Enter.
5
Press Stop/Clear to return to Standby mode.
Setting print job timeout
You can set the amount of time a single print job is active before it must
print.
print.
The machine handles incoming data as a single job if it comes in within
the specified time. When an error occurs while processing data from the
computer and the data flow stops, the machine waits the specified time
and then cancels printing if data flow does not resume.
the specified time. When an error occurs while processing data from the
computer and the data flow stops, the machine waits the specified time
and then cancels printing if data flow does not resume.
1
Press Menu until System Setup appears on the bottom line of the
display and press Enter.
display and press Enter.
2
Press Enter when Machine Setup appears.
3
Press the Scroll buttons until Job Timeout appears and press
Enter.
Enter.
4
Press the Scroll buttons until the time setting you want appears and
press Enter.
press Enter.
5
Press Stop/Clear to return to Standby mode.