Roland VP-770 用户手册
84
REGIST PEDAL
Parameter
Value
Description
Hold Part
Specifi es the part(s) that will be controlled by the hold pedal.
VOC/ENS
Vocal Designer part and Ensemble part.
VOC
Vocal Designer part only.
ENS
Ensemble part only.
P1 Asgn
P2 Asgn
P2 Asgn
Specifi es the function that will be controlled by the control pedal.
OFF
Off
MOD
Applies modulation.
DYN1
Changes the volume. Transmits MIDI message CC#2 (breath control) to the
sound generator section. This is the same operation as Voice Expression
(p. 66), and will operate only in the positive (+) direction to increase the
volume.
sound generator section. This is the same operation as Voice Expression
(p. 66), and will operate only in the positive (+) direction to increase the
volume.
DYN2
Changes the volume. Transmits MIDI message CC#4 (foot control) to the
sound generator section. For STRINGS and BRASS sounds, this allows the
volume to be controlled in the ± directions (it will not go to zero). For other
sounds, the volume can be controlled only in the “+” direction.
sound generator section. For STRINGS and BRASS sounds, this allows the
volume to be controlled in the ± directions (it will not go to zero). For other
sounds, the volume can be controlled only in the “+” direction.
EXP
Changes the volume. Transmits MIDI message CC#11 (expression) to the
sound generator section. The volume is controlled in a range of 0–127.
sound generator section. The volume is controlled in a range of 0–127.
FILTER
Changes the tone.
WAH
Applies a wah pedal eff ect to sounds that support Wah.
PIZZ/STAC
Plays the pizzicato or staccato sound (only for supported tones).
FALL/TREM
Plays the fall or tremolo sound (only for supported tones).
UNI/STK
Switches between unison mode and stack mode (only for supported tones).
DOIT
Applies a doit eff ect (only for supported tones).
PORT
Applies a portamento eff ect.
AMB
Controls the depth of ambience.
DIR-MIC
Controls the direct microphone volume.
PANEL-SW
Performs the operation specifi ed for P1 Sw Asgn/P2 Sw Asgn.
P1 Sw Asgn
P2 Sw Asgn
P2 Sw Asgn
If P1 Asgn/P2 Asgn is set to “PANEL-SW,” this specifi es the operation that
occurs when the control pedal turns on.
occurs when the control pedal turns on.
REC/PLAY
Same operation as Sound Looper [REC/PLAY] button.
Rapidly pressing the pedal twice performs the same operation as the [STOP] button.
*
STOP
Perform the same operation as Sound Looper [STOP] button.
P1 Part
P2 Part
P2 Part
Specifi es the part(s) that will be controlled by the control 1/2 pedals.
VOC/ENS
Vocal Designer part and Ensemble part.
VOC
Vocal Designer part only.
ENS
Ensemble part only.
REGIST S1/S2
Parameter
Value
Description
Sw1 Assign
Sw2 Assign
Sw2 Assign
Specify the functions that will be controlled by the [S1]/[S2] buttons.
OFF
Off
PIZZ/STAC
The pizzicato or staccato sound will be heard (only for supported tones).
FALL/TREM
The fall or tremolo sound will be heard (only for supported tones).
UNI/STK
Switches between unison mode and stack mode (only for supported tones).
DOIT
Applies the doit eff ect (only for supported tones).
PORT-ENS
Applies the portamento eff ect to the Ensemble.
PORT-VOC
Applies the portamento eff ect to the Vocal Designer.
AMB-OFF
Switches the ambience when you press the button.
DIR-MIC-OFF
Switches the direct microphone when you press the button.
Sw1 Mode
Sw2 Mode
Sw2 Mode
Turns the [S1]/[S2] buttons function LATCH/MOMENTARY.
LATCH
The on/off status will alternate each time you press [S1]/[S2] button.
MOMENTARY
The status will be on only while you hold down [S1]/[S2] button.