Roland VP-770 用户手册
98
SYSTEM SOUND
Here you can make sound-related settings.
Parameter
Value
Description
Master Tune
415.3–466.2 (Hz)
Adjusts the overall tuning of the VP-770. The display shows the frequency of
the A4 note (center A).
the A4 note (center A).
Master Key Shift
-24–+24
Shifts the overall pitch of the VP-770 in semitone steps.
Master Level
0–127
Adjusts the volume of the entire VP-770.
Output Gain
-12–+12 (dB)
This adjusts the output gain from the VP-770’s Analog Out and Digital
Out. When, for example, there are relatively few voices being sounded,
boosting the output gain can let you attain the most suitable output level for
recording and other purposes.
Out. When, for example, there are relatively few voices being sounded,
boosting the output gain can let you attain the most suitable output level for
recording and other purposes.
Out B Assign
Selects the audio signals that will be sent from the rear panel OUTPUT B
jacks.
jacks.
AMB
Sound output from the OUTPUT A jacks
Direct sound (Vocal Designer, Ensemble, Bass & Percussion,
Audio Key, Sound Looper)
Audio Key, Sound Looper)
Sound output from the OUTPUT B jacks
Ambience component (Vocal Designer, Ensemble,
Bass & Percussion, Audio Key)
Bass & Percussion, Audio Key)
ENS
Sound output from the OUTPUT A jacks
Vocal Designer, Bass & Percussion, Audio Key, Sound Looper,
ambience component (Vocal Designer, Bass & Percussion,
Audio Key)
ambience component (Vocal Designer, Bass & Percussion,
Audio Key)
Sound output from the OUTPUT B jacks
Ensemble
AKEY
Sound output from the OUTPUT A jacks
Vocal Designer, Ensemble, Bass & Percussion,
ambience component (Vocal Designer, Ensemble,
Bass & Percussion)
ambience component (Vocal Designer, Ensemble,
Bass & Percussion)
Sound output from the OUTPUT B jacks
Audio Key, Sound Looper
AudioKey Level
0–127
Specifi es the volume of the AudioKey.
AudioKey Amb Send
0–127
Specifi es the level of the signal sent to the ambience for the AudioKey.
Voice Exp Sens
0–127
You can adjust the sensitivity at which the Voice Expression (p. 66) eff ect will
begin applying in response to changes in microphone input loudness over.
Higher sensitivity settings mean that the Voice Expression eff ect will begin
applying even when your voice is still at a low loudness level.
Lower sensitivity settings mean that the Voice Expression eff ect will begin
applying only when your voice reaches a fairly high loudness level. You’ll
fi nd it easier to control Voice Expression if you set this to a sensitivity that’s
appropriate for your singing voice.
begin applying in response to changes in microphone input loudness over.
Higher sensitivity settings mean that the Voice Expression eff ect will begin
applying even when your voice is still at a low loudness level.
Lower sensitivity settings mean that the Voice Expression eff ect will begin
applying only when your voice reaches a fairly high loudness level. You’ll
fi nd it easier to control Voice Expression if you set this to a sensitivity that’s
appropriate for your singing voice.
Preset Protect
ON, OFF
With the factory settings, registrations cannot be saved at the preset buttons.
If you turn Preset Protect OFF, registrations can be saved in the preset
buttons as well (p. 78).
If you turn Preset Protect OFF, registrations can be saved in the preset
buttons as well (p. 78).
SYSTEM METRONOME
Here you can make metronome-related settings.
Parameter
Value
Description
Metro Mode
OFF
The metronome will not sound.
PLAY-ONLY
The metronome will sound only while the Sound Looper is playing back.
REC-ONLY
The metronome will sound only while the Sound Looper is recording.
PLAY&REC
The metronome will sound while the Sound Looper is playing or recording.
ALWAYS
The metronome will sound constantly.
Metro Level
0–10
Adjusts the volume of the metronome.