Motorola MT2070 用户手册
Accessories 13 - 3
Single Slot Cradles
The STB2000-C10007R, STB2078-C10007WR and STB2000-F10007R cordless device cradles act as chargers
and host communication interfaces for the MT2000 Series cordless devices. Cradles can sit on a desktop, mount
on a wall or mount on a forklift (STB2000-F only). Any discussion of transmission of information refers specifically
to cradles with Bluetooth technology.
and host communication interfaces for the MT2000 Series cordless devices. Cradles can sit on a desktop, mount
on a wall or mount on a forklift (STB2000-F only). Any discussion of transmission of information refers specifically
to cradles with Bluetooth technology.
Cradle Features
See
.
Battery Charging in the Cradle
Single slot cradles act as power pass throughs to the device allowing the device to charge the Li-ion battery in the
device. A complete charge of a fully discharged battery can take up to four hours using external power and up to 10
hours using the interface cable.
device. A complete charge of a fully discharged battery can take up to four hours using external power and up to 10
hours using the interface cable.
To charge the device:
1.
Connect the single slot USB cradle to a power source.
2.
Insert the battery into the battery slot in the device noting the battery polarity.
3.
Insert the top of the device into the cradle first, then firmly press the device into place. The device’s green
charge LED indicates the device battery charging status.
charge LED indicates the device battery charging status.
4.
When charging is completed, the green LED is off (default) and the device can be lifted out of the cradle.
Changing the Host Interface
To connect to a different host, or to the same host using a different cable:
1.
Disconnect the power supply from the cradle, if applicable.
2.
Disconnect the interface cable from the host.
NOTE
Use ONLY a LISTED Motorola, Type no. 50-14000 (5-14Vdc/ 1.5A min.), or PWRS-14000 (5-14Vdc/ 1.5A
min.), Direct Plug-In Power supply, marked Class 2 or LPS (IEC60950-1, SELV). Use of alternative Power
Supply will invalidate any approvals given to this unit and may be dangerous.
min.), Direct Plug-In Power supply, marked Class 2 or LPS (IEC60950-1, SELV). Use of alternative Power
Supply will invalidate any approvals given to this unit and may be dangerous.
Verwenden Sie NUR ein von Motorola GELISTETES, mit der Typnummer 50-14000 (5-14 VDC/mindestens
1,5 A) oder PWRS-14000 (5-14 VDC/mindestens 1,5 A) markiertes, Direct Plug-In-Netzteil, das als Klasse 2
oder LPS (IEC60950-1, SELV) gekennzeichnet ist. Bei Verwendung eines anderen Netzteils werden alle für
das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.
1,5 A) oder PWRS-14000 (5-14 VDC/mindestens 1,5 A) markiertes, Direct Plug-In-Netzteil, das als Klasse 2
oder LPS (IEC60950-1, SELV) gekennzeichnet ist. Bei Verwendung eines anderen Netzteils werden alle für
das Gerät gewährten Genehmigungen außer Kraft gesetzt, und der Betrieb kann gefährlich sein.
NOTE
To charge the battery for your device, battery and charger temperatures must be between +32° F and +104° F
(0° C to +40° C).
(0° C to +40° C).
NOTE
If the battery is completely discharged, and the unit is powered from a USB or RS232 cable, it may take up
to two hours for the unit to power up.There is no indication to the user of this condition and it may appear
that the unit is not charging and/or not working correctly. However, if the unit is placed in an STB2000 or
STB2078 cradle with the 12V power supply power up is immediate.
to two hours for the unit to power up.There is no indication to the user of this condition and it may appear
that the unit is not charging and/or not working correctly. However, if the unit is placed in an STB2000 or
STB2078 cradle with the 12V power supply power up is immediate.
NOTE
The default state of the LED is off when the battery is fully charged with the exception of several initial
charge cycles. The LED may continually blink until the battery goes through several discharge cycles to
calibrate itself.
charge cycles. The LED may continually blink until the battery goes through several discharge cycles to
calibrate itself.