Cisco Systems WRT110 用户手册

下载
页码 48
Chapter 3
Advanced Configuration
18
RangePlus Wireless Router
Wireless Client List
Wireless Client List
This  screen  shows  computers  and  other  devices  on 
the wireless network. The list can be sorted by Client 
Name, Interface, IP Address, MAC Address, and Status. 
Select Save to MAC Address Filter List for any device 
you want to add to the MAC Address Filter List. Then 
click Add
To  retrieve  the  most  up-to-date  information,  click 
Refresh. To exit this screen and return to the Wireless 
MAC Filter screen, click Close.
MAC 1-50 
Enter the MAC addresses of the devices whose 
wireless access you want to block or allow.
Click Save Settings to apply your changes, or click Cancel 
Changes to cancel your changes.
Wireless > Advanced Wireless Settings
This  Advanced  Wireless  Settings  screen  is  used  to  set  up 
the Router’s advanced wireless functions. These settings 
should  only  be  adjusted  by  an  expert  administrator  as 
incorrect settings can reduce wireless performance.
Wireless > Advanced Wireless Settings
Advanced Wireless
AP Isolation 
This isolates all wireless clients and wireless 
devices on your network from each other. Wireless devices 
will  be  able  to  communicate  with  the  Router  but  not 
with each other. To use this function, select Enabled. AP 
Isolation is disabled by default. 
Frame  Burst 
Enabling  this  option  should  provide  your 
network  with  greater  performance,  depending  on  the 
manufacturer of your wireless products. To use this option, 
keep the default, Enabled. Otherwise, select Disabled.
Authentication Type 
The  default  is  set  to  Auto,  which 
allows either Open System or Shared Key authentication 
to be used. With Open System authentication, the sender 
and the recipient do NOT use a WEP key for authentication. 
With Shared Key authentication, the sender and recipient 
use a WEP key for authentication. Select Shared Key to 
only use Shared Key authentication.
Basic Rate 
The Basic Rate setting is not actually one rate 
of transmission but a series of rates at which the Router 
can transmit. The Router will advertise its Basic Rate to the 
other wireless devices in your network, so they know which 
rates will be used. The Router will also advertise that it will 
automatically  select  the  best  rate  for  transmission.  The 
default setting is Default, when the Router can transmit 
at all standard wireless rates (1-2Mbps, 5.5Mbps, 11Mbps, 
18Mbps,  and  24Mbps).  Other  options  are  1-2Mbps,  for 
use  with  older  wireless  technology,  and  All,  when  the 
Router  can  transmit  at  all  wireless  rates. The  Basic  Rate 
is not the actual rate of data transmission. If you want to 
specify  the  Router’s  rate  of  data  transmission,  configure 
the Transmission Rate setting.
Transmission Rate 
The rate of data transmission should 
be set depending on the speed of your wireless network. 
You can select from a range of transmission speeds, or you 
can select Auto to have the Router automatically use the 
fastest  possible  data  rate  and  enable  the  Auto-Fallback 
feature.  Auto-Fallback  will  negotiate  the  best  possible 
connection  speed  between  the  Router  and  a  wireless 
client. The default is Auto.
N  Transmission  Rate 
The  rate  of  data  transmission 
should be set depending on the speed of your Wireless-N 
networking. You can select from a range of transmission 
speeds,  or  you  can  select  Auto  to  have  the  Router 
automatically use the fastest possible data rate and enable 
the Auto-Fallback feature. Auto-Fallback will negotiate the 
best possible connection speed between the Router and a 
wireless client. The default is Auto.
CTS  Protection  Mode 
The  Router  will  automatically 
use  CTS  (Clear-To-Send)  Protection  Mode  when  your 
Wireless-N  and  Wireless-G  products  are  experiencing 
severe  problems  and  are  not  able  to  transmit  to  the 
Router in an environment with heavy 802.11b traffic. This 
function boosts the Router’s ability to catch all Wireless-