Abocom FM560MX 用户手册
FCC REGULATORY STATEMENTS
FCC Part 68 Registration
This device complies with FCC Part 68 rules, and the use of this device is subject
to the following restrictions:
1.
This device complies with FCC Part 68 rules, and the use of this device is subject
to the following restrictions:
1.
The FCC has established rules which permit this device to be directly
connected to the telephone network. Standardized jacks are used for these
connections. This equipment should not be used on party lines or coin
phones.
connected to the telephone network. Standardized jacks are used for these
connections. This equipment should not be used on party lines or coin
phones.
2.
If this device is malfunctioning, it may also be causing harm to the
telephone network; this device should be disconnected until the source of
the problem can be determined and until repair has been made. If this is
not done, the telephone company may temporarily disconnect service.
telephone network; this device should be disconnected until the source of
the problem can be determined and until repair has been made. If this is
not done, the telephone company may temporarily disconnect service.
3.
The telephone company may make changes in it's facilities, equipment,
operation and procedures; if such changes affect the compatibility or use
of this device, the telephone company is required to give adequate notice
of the situation with the FCC.
operation and procedures; if such changes affect the compatibility or use
of this device, the telephone company is required to give adequate notice
of the situation with the FCC.
4.
If the telephone company requests information on what equipment is
connected to their lines, inform them of the following:
a.
connected to their lines, inform them of the following:
a.
The telephone number to which this unit is connected.
b.
The Ringer Equivalence Number (REN).
c.
The USOC jack required.
d.
The FCC Registration number.
Items (b) and (d) are indicated on the label. The Ringer Equivalence Number
(REN) is used to determine how many devices can be connected to your telephone
line. In most areas, the sum of the REN's of all the devices on any one line should
not exceed 5.0. If too many devices are attached, they may not ring properly.
FCC Part 15 Registration
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1.
(REN) is used to determine how many devices can be connected to your telephone
line. In most areas, the sum of the REN's of all the devices on any one line should
not exceed 5.0. If too many devices are attached, they may not ring properly.
FCC Part 15 Registration
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the distance between the equipment and receiver
3.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
which the receiver is connected.
4.
Consult an experienced radio/TV technician for help.
Caution: Change or modifications not expressly approved by party responsible
for compliance could void the user’s authority to operate the equipment.
CTR 21 pan-European Certification
This equipment has been approved in accordance with Council Decision
98/482/EC for pan-European single terminal connection to the public switched
telephone network (PSTN). However, due to differences between the individual
PSTNs provided in different countries, the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point. In the event of problems, you should contact your equipment
supplier in the first instance.
This device is designed to work with the notified networks in all EC member
states. Nevertheless, some of the network services in invidual countries might not
be supported, but they will not affect the normal data and fax applications. For
example, the metering charge service in Germany. Besides you may encounter
difficulty of using PULSE dialing function in some of the countries, such as
Nordic countries. This kind of network compatibility is dependent on the physical
and software settings of this device. If the users are desired to use this device on
those networks, they should contact the vendor or supplier first.
for compliance could void the user’s authority to operate the equipment.
CTR 21 pan-European Certification
This equipment has been approved in accordance with Council Decision
98/482/EC for pan-European single terminal connection to the public switched
telephone network (PSTN). However, due to differences between the individual
PSTNs provided in different countries, the approval does not, of itself, give an
unconditional assurance of successful operation on every PSTN network
termination point. In the event of problems, you should contact your equipment
supplier in the first instance.
This device is designed to work with the notified networks in all EC member
states. Nevertheless, some of the network services in invidual countries might not
be supported, but they will not affect the normal data and fax applications. For
example, the metering charge service in Germany. Besides you may encounter
difficulty of using PULSE dialing function in some of the countries, such as
Nordic countries. This kind of network compatibility is dependent on the physical
and software settings of this device. If the users are desired to use this device on
those networks, they should contact the vendor or supplier first.