ATTO Technology 2390C/R/D 用户指南
vi
Command explanations
AutoLogSense
Controls whether current data from log pages in a SCSI
target device is available automatically.
Controls whether current data from log pages in a SCSI
target device is available automatically.
Default: disabled
set AutoLogSense [enabled|disabled]
Requires a SaveConfiguration command
get AutoLogSense
set AutoLogSense [enabled|disabled]
Requires a SaveConfiguration command
get AutoLogSense
AutoMap
Automatically assigns a subset of source protocol LUNs
to a subset of target destination devices visible to the
FibreBridge. All previous maps are deleted.The unit
reports a five-second delay while it scans for devices.
Automatically assigns a subset of source protocol LUNs
to a subset of target destination devices visible to the
FibreBridge. All previous maps are deleted.The unit
reports a five-second delay while it scans for devices.
enabled: AutoMap <fp>
All other models and FC2400 with FCMultiNode disabled:
AutoMap
Requires a SaveConfiguration command
BootFibreDelay
Regulates the delay (in seconds) which the FibreBridge
waits until after startup before enabling Fibre Channel
ports.
Regulates the delay (in seconds) which the FibreBridge
waits until after startup before enabling Fibre Channel
ports.
Default: 0 (no delay)
set BootFibreDelay [0 | 15 | 30 | 45| 60 | 75]
Requires a SaveConfiguration command
get BootFibreDelay
set BootFibreDelay [0 | 15 | 30 | 45| 60 | 75]
Requires a SaveConfiguration command
get BootFibreDelay
BootScan
Provides dynamic mapping of SCSI devices to the Fibre
port/LUN combination via a SCSI bus scan at boot time.
All devices discovered during the bus scans are assigned
to a Fibre port, Fibre LUN combination until the next
reset/power cycle. This dynamic mapping replaces the
current, static mapping of the FibreBridge.
Provides dynamic mapping of SCSI devices to the Fibre
port/LUN combination via a SCSI bus scan at boot time.
All devices discovered during the bus scans are assigned
to a Fibre port, Fibre LUN combination until the next
reset/power cycle. This dynamic mapping replaces the
current, static mapping of the FibreBridge.
Default: disabled
set BootScan [enabled | disabled]
Requires a SaveConfiguration command
get BootScan
set BootScan [enabled | disabled]
Requires a SaveConfiguration command
get BootScan
BootScanPorts (FB2400 only)
Regulates the ports to be used for a boot scan.
Regulates the ports to be used for a boot scan.
Default: auto
set BootScanPorts [fp | all | auto]
Requires a SaveConfiguration command
get BootScanPorts
set BootScanPorts [fp | all | auto]
Requires a SaveConfiguration command
get BootScanPorts
BridgeModel
Reports model and firmware information about the
FibreBridge.
Reports model and firmware information about the
FibreBridge.
get BridgeModel
BridgeName
Specifies the eight-character ASCII name assigned to the
FibreBridge used to identify individual units. It is not the
World Wide Name. The string is alphanumeric, eight
characters long,. Changes take effect immediately.
Specifies the eight-character ASCII name assigned to the
FibreBridge used to identify individual units. It is not the
World Wide Name. The string is alphanumeric, eight
characters long,. Changes take effect immediately.
Default: “ “
set BridgeName [name]
get BridgeName
set BridgeName [name]
get BridgeName
ClearEventLog
Clears the contents of the event log. No new entries are
recorded until the operation is completed.
Clears the contents of the event log. No new entries are
recorded until the operation is completed.
ClearEventLog
ClearTraceLog
Clears the contents of the trace log. No events are
recorded until the operation is completed.
Clears the contents of the trace log. No events are
recorded until the operation is completed.
ClearTraceLog
Date
Sets/displays the date. The range is 01/01/2000 to
12/31/2099.
Sets/displays the date. The range is 01/01/2000 to
12/31/2099.
Default: 01/01/2000
set Date [MM] / [DD] / [YYYY]
Requires a SaveConfiguration command
get Date
set Date [MM] / [DD] / [YYYY]
Requires a SaveConfiguration command
get Date
DeleteAllMaps
Removes all mapped devices from the map table. Upon
the subsequent POST, if no maps are present, the default
maps are loaded.
Removes all mapped devices from the map table. Upon
the subsequent POST, if no maps are present, the default
maps are loaded.
DeleteAllMaps
Requires a SaveConfiguration command
Requires a SaveConfiguration command
DHCPFixedDelay
Regulates or displays the delay (in seconds) between
DHCP client request intervals.
Regulates or displays the delay (in seconds) between
DHCP client request intervals.
Default: 0
set DHCPFixedDelay [0-255]
Requires a SaveConfiguration Restart command
get DHCPFixedDelay
set DHCPFixedDelay [0-255]
Requires a SaveConfiguration Restart command
get DHCPFixedDelay