Runco CL-610LT 用户手册
39
Runco CL-610 Owner’s Operating Manual
On-Screen Display Menus
Setup
To access advanced picture quality adjustments, use the up- or down-arrow keys to
highlight
highlight
Set Up and press Enter. Use the number buttons on the remote to enter the
Set Up menu passcode when prompted and press
Enter again. Then, press MENU
on the remote control.
Runco CL-610
> Video
S-Video
Component1
Component2
RGB-HD
HDMI
------------------------
Aspect Ratio
Installation
Option
Set Up
ISF Calibration
Passcode
Please Enter
Passcode To
Passcode To
Access Service
Screen
* * *
Passcode
Please Enter
Passcode To
Passcode To
Access Service
Screen
Confirmed
➤
White Balance
NOTE: You only need to enter the Set Up menu passcode the first time you select that
menu after turning on the projector.
menu after turning on the projector.
Gamma: “Gamma” is a global setting that determines how gray shades are displayed
between minimum input (black) and maximum input (white) for all signals. A good
gamma setting helps to optimize blacks and whites while ensuring smooth transitions
for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast”
controls, the overall tone of your images can be lightened or darkened without changing
the extremes and all images will be more vibrant while still showing good detail in dark
areas when using the “Gamma” control.
In all but the most unusual situations, the appropriate “Gamma Selection” (see below)
will produce accurate colors and a satisfying contrast level. However, it is sometimes
necessary to adjust the red, blue and green gamma curves individually. To do this,
select Gamma from the White Balance sub-menu and use the left- and right-arrow
buttons to manipulate the on-screen slidebars.
Gain: Use the Gain controls in the White Balance sub-menu to correct color imbalances
in the bright areas of the image. A good way to do this is to use a test pattern consisting
mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas
contain traces of red, green or blue, decrease the Gain for that color.
Offset: Use the Offset controls in the White Balance sub-menu to correct color
imbalances in the dark areas of the image. A good way to do this is to use a test pattern
consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray
areas contain traces of red, green or blue, decrease the Offset for that color.
Store Color Temp.4/Store Color Temp.5: When you are finished adjusting the
Gamma, Gain and Offset, select Store Color Temp.4 or Store Color Temp.5 to store
your settings. To recall them, set the Color Temperature to +4 or +5 in the Image
Adjustment menu (refer to “Picture Quality Adjustments,” earlier in this section).
between minimum input (black) and maximum input (white) for all signals. A good
gamma setting helps to optimize blacks and whites while ensuring smooth transitions
for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast”
controls, the overall tone of your images can be lightened or darkened without changing
the extremes and all images will be more vibrant while still showing good detail in dark
areas when using the “Gamma” control.
In all but the most unusual situations, the appropriate “Gamma Selection” (see below)
will produce accurate colors and a satisfying contrast level. However, it is sometimes
necessary to adjust the red, blue and green gamma curves individually. To do this,
select Gamma from the White Balance sub-menu and use the left- and right-arrow
buttons to manipulate the on-screen slidebars.
Gain: Use the Gain controls in the White Balance sub-menu to correct color imbalances
in the bright areas of the image. A good way to do this is to use a test pattern consisting
mostly of solid white areas, such as an 80 IRE “window” pattern. If the white areas
contain traces of red, green or blue, decrease the Gain for that color.
Offset: Use the Offset controls in the White Balance sub-menu to correct color
imbalances in the dark areas of the image. A good way to do this is to use a test pattern
consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the gray
areas contain traces of red, green or blue, decrease the Offset for that color.
Store Color Temp.4/Store Color Temp.5: When you are finished adjusting the
Gamma, Gain and Offset, select Store Color Temp.4 or Store Color Temp.5 to store
your settings. To recall them, set the Color Temperature to +4 or +5 in the Image
Adjustment menu (refer to “Picture Quality Adjustments,” earlier in this section).