Toshiba TDP-S20 用户手册
33
Operations
32
Using the menu (Continued)
■
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Description
Computer Y/P
B
/P
R
Video
Camera
S-video
Input
Input source name
Yes
Yes
Yes
Yes
Mode name
RGB input mode
[Note 1]
Yes
No
No
No
H-resolution
Horizontal resolution (in dots)
Yes
No
No
No
V-resolution
Vertical resolution (in dots)
Yes
No
No
No
H-frequency
Horizontal sync frequency
Yes
No
No
No
V-frequency
Vertical sync frequency
[Note 2]
Yes
No
No
No
Sync
Sync signal polarity
[Note 3]
Yes
No
No
No
Signal format
Y/P
B
/P
R
signal format
No
Yes
No
No
Video mode
Color method of video signal
No
No
Yes
No
Lamp time
Time of lamp use
[Note 4]
Yes
Yes
Yes
Yes
Lamp reset count
The count for lamp replacement
Yes
Yes
Yes
Yes
Total time
The total time that this projector is used
Yes
Yes
Yes
Yes
Version
Firmware version
[Note 5]
Yes
Yes
Yes
Yes
Notes
1: The mode of supported RGB signals
1: The mode of supported RGB signals
is shown.
2: Same as the refresh rate of the computer signal.
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
3: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
4: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) When the displayed time approaches 3,000 hours, consult
with a store about getting a TLPLV4 replacement lamp (sold separately) prepared.
with a store about getting a TLPLV4 replacement lamp (sold separately) prepared.
5: [Version] shows the version of the projector’s internal control program. This version is referred
to for customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
■
The default setting menu
This menu shows placement status and other settings.
Set the timer to wait for the power to be turned off after signal input stops.
Press . Switch with and .
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Press . Switch with and .
Off (not turned off)/1 min./5 min./10 min./30 min./60 min.
Set whether the input with signals is only selected or not.
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual Auto
(Manual), or when the power cord is plugged in (Auto). Manual Auto
Sets the lamp power.
Sets the cooling fan speed.
Press .
Resets all adjustments and settings to their factory settings.
Resets all adjustments and settings to their factory settings.
Description
Item
Projection
mode
mode
No signal
power off
power off
Auto input
search
search
Power on
Lamp power
[Note 1]
Fan mode
[Note 2]
Reset all
(Rear mounted
from ceiling)
from ceiling)
(Standard)
(Rear)
(Mounted
from ceiling)
On Off
Standard High
Yes No
Low Standard
Notes
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
1: When Lamp power is set to Low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off.
2: Setting [Fan mode] to [High] increases the cooling fan speed. Set this option to use the projector,
for example, at high altitude (over 1,500 meters above sea level).
Notes
• Note that in the event of a power outage but the power is restored afterwards, the projector
power will come on if Power on is set to Auto, and the power cord is plugged in.
• When you turn off the projector even if Power on is set to Auto, you must press the ON/
STANDBY button to turn the power off.