JVC DLA-M5000SCE 用户手册
18
DLA-M5000CLE (Re)/ LCT0979-002A / ENGLISH
Connecting to Various Devices
* Before connection, be sure to turn off the projector and connected devices.
* Read the manual which comes with each device thoroughly.
* Read the manual which comes with each device thoroughly.
Signals that Can Be Input to the Projector
The following signals can be input to the projector:
■ Video signals
(1) Response to color systems
*1: Responds if Y/C output is available.
*2: Signifies that component signals (“Y, P
*2: Signifies that component signals (“Y, P
B
, P
R
” / “Y, B-Y, R-Y” / “G, B, R, H/C
S
, V”) conform to the signal timing
(synchronization and video period) of each color system. The color systems are used for convenience only.
*3: To use these terminals, a video board (separately sold) is required.
(2) Response to double density (*1), high-vision signals
*4: Signals whose density of scanning lines/field is twice as high.
*5: Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line
*5: Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line
doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded 525P
progressive signals.
progressive signals.
Note
• DTV-format signals (480i, 480p, 720p, 1080i) can be input into this unit (Y, P
B
/B-Y, P
R
/R-Y input terminals).
For details about DTV-format signals (480i, 480p, 720p, 1080i) compatible with this unit, refer to page 65.
■ Computer signals
• Signals with the following resolutions can be input to the input terminal of RGB IN-1 (PC) or RGB IN-2 (G, B, R, H/C
S
, V).
(The following signals are preset.)
Notes
• Interlace signals are not handled.
• Some signals other than listed above can be displayed. But they require adjustment. Even some of the signals listed above
• Some signals other than listed above can be displayed. But they require adjustment. Even some of the signals listed above
may require adjustment depending on the video board used.
• When a signal other than listed above is input, the screen could be partially erased or an unneeded fold-over screen could
appear.
• Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
• Composite sync.(C
• Composite sync.(C
S
) and G on sync. signals can not handled depending on the devices connected.
Color system
Input terminal
NTSC 480i
NTSC 4.43
PAL
SECAM
VIDEO*
3
‡
‡
‡
‡
Y/C*
3
‡
‡
*
1
‡
-----
Y, P
B
/B-Y, P
R
/R-Y
‡
*
1
‡
*
2
‡
*
2
‡
*
2
G, B, R, H/C
S
, V
‡
*
2
‡
*
2
‡
*
2
‡
*
2
Input terminal
NTSC*
2222
High-vision signal
Y, P
B
/B-Y, P
R
/R-Y
‡
‡
G, B, R, H/C
S
, V
‡
‡
Screen resolution (standard name)
Horizontal frequency
Vertical frequency
Scanning method
640
× 400 (PC-9801)
24.8kHz
56.4Hz
Non-interlace
640
× 350 (VGA1)
31.5kHz
70.1Hz
Non-interlace
640
× 480 (VGA3)
31.5kHz
59.9Hz
Non-interlace
640
× 480 (Macintosh 13")
35.0kHz
66.7Hz
Non-interlace
640
× 480 (VGA VESA)
37.5kHz
75.0Hz
Non-interlace
800
× 600 (SVGA1)
37.9kHz
60.3Hz
Non-interlace
800
× 600 (SVGA2)
48.1kHz
72.2Hz
Non-interlace
832
× 624 (Macintosh 16")
49.7kHz
74.6Hz
Non-interlace
1024
× 768 (XGA1)
48.4kHz
60.0Hz
Non-interlace
1024
× 768 (XGA2)
56.5kHz
70.1Hz
Non-interlace
1024
× 768 (Macintosh 19")
60.2kHz
74.9Hz
Non-interlace
1152
× 870 (Macintosh 21")
68.7kHz
75.0Hz
Non-interlace
1280
× 1024 (SXGA1)
64.0kHz
60.0Hz
Non-interlace
1280
× 1024 (SXGA2)
70.8kHz
67.0Hz
Non-interlace
1360
× 1024 (SXGA3: Mac Board)
80.0kHz
75.1Hz
Non-interlace
DLA-M5000LE&SCE Eng Re.book Page 18 Tuesday, March 12, 2002 3:59 PM