Xerox 3435DN 用户手册
9.13
<Troubleshooting>
Common Windows problems
Note
Refer to Microsoft Windows 2000/XP/2003 User’s Guide that
came with your PC for further information on Windows error
messages.
came with your PC for further information on Windows error
messages.
Curl
If the printed paper is curled or paper does not
feed into the printer:
• Turn over the stack of paper in the tray. Also try
feed into the printer:
• Turn over the stack of paper in the tray. Also try
rotating the paper 180° in the tray.
• Try printing to rear cover.
An unknown
image
repetitively
appears on a
next few sheets
or loose toner,
light print, or
contamination
occurs.
image
repetitively
appears on a
next few sheets
or loose toner,
light print, or
contamination
occurs.
Your printer is probably being used at an altitude
of 1,000 m (3,281 ft) or above.
The high altitude may affect the print quality such
as loose toner or light imaging. You can set this
option through Printer Settings Utility or
Altitude Adj. in System setup menu. See
of 1,000 m (3,281 ft) or above.
The high altitude may affect the print quality such
as loose toner or light imaging. You can set this
option through Printer Settings Utility or
Altitude Adj. in System setup menu. See
Condition
Suggested solutions
“File in Use”
message appears
during installation.
message appears
during installation.
Exit all software applications. Remove all
software from the StartUp Group, then restart
Windows. Reinstall the printer driver.
software from the StartUp Group, then restart
Windows. Reinstall the printer driver.
“Error Writing to
LPTx” message
appears.
LPTx” message
appears.
• Ensure that the cables are connected
correctly, the printer is on.
• If bi-directional communication is not turned
on in the driver, it will also cause this
message.
message.
“General Protection
Fault”, “Exception
OE”, “Spool32”, or
“Illegal Operation”
messages appear.
Fault”, “Exception
OE”, “Spool32”, or
“Illegal Operation”
messages appear.
Close all other applications, reboot Windows
and try printing again.
and try printing again.
“Fail To Print,” “A
printer timeout error
occurred,”
messages appear.
printer timeout error
occurred,”
messages appear.
These messages may appear during printing.
Just keep waiting until the printer finishes
printing. If the message appears in standby
mode or after printing has been completed,
check the connection and/or whether an error
has occurred.
Just keep waiting until the printer finishes
printing. If the message appears in standby
mode or after printing has been completed,
check the connection and/or whether an error
has occurred.
Condition
Suggested solutions
Common PostScript problems
The following situations are PostScript language specific and may occur
when several printer languages are being used.
when several printer languages are being used.
Note
To receive a printed or screen displayed message when
PostScript errors occur, open the Print Options window and
click the desired selection next to the PostScript errors section.
PostScript errors occur, open the Print Options window and
click the desired selection next to the PostScript errors section.
Condition
Possible cause
Suggested solutions
PostScript file
can not be
printed.
can not be
printed.
The PostScript
driver may not
be installed
correctly.
driver may not
be installed
correctly.
• Print a configuration page
and verify that the PostScript
version is available for
printing.
version is available for
printing.
• Install the PostScript driver.
• If problem consists, contact a
• If problem consists, contact a
service representative.
“Limit Check
Error” message
appears.
Error” message
appears.
The print job
was too
complex.
was too
complex.
You might need to reduce the
complexity of the page or install
more memory.
complexity of the page or install
more memory.
A PostScript
error page
prints.
error page
prints.
Print job may
not be
PostScript.
not be
PostScript.
Make sure that the print job is a
PostScript job. Check to see
whether the software
application expected a setup or
PostScript header file to be sent
to the printer.
PostScript job. Check to see
whether the software
application expected a setup or
PostScript header file to be sent
to the printer.
The optional
tray 2 is not
selected in the
driver.
tray 2 is not
selected in the
driver.
The printer
driver has not
been
configured to
recognize the
optional tray 2.
driver has not
been
configured to
recognize the
optional tray 2.
Open the PostScript driver
properties, select the Device
Settings tab, and set the Tray2
option of the Installable
Options section to Installed.
properties, select the Device
Settings tab, and set the Tray2
option of the Installable
Options section to Installed.