3com 5500 用户手册
![3com](https://files.manualsbrain.com/attachments/960452ff43b9899cbcffced60c87abf956e7967a/common/fit/150/50/f6ac125d7af2cf40fec58935fa6d4bf71457a57efe50bee91208a434f325/brand_logo.jpeg)
Remote Port Mirroring Configuration
235
3 Configuration on the destination switch (Switch C)
#
mirroring-group 1 remote-destination
#
vlan 10
remote-probe vlan enable
#
interface Ethernet1/0/1
port link-type trunk
port trunk permit vlan 1 10
#
interface Ethernet1/0/2
port access vlan 10
mirroring-group 1 monitor-port
#
Precautions
Note the following when configuring the source switch:
■
All ports in a remote source mirroring group are on the same switch (the source
switch). A remote source mirroring group can have only one reflector port.
switch). A remote source mirroring group can have only one reflector port.
■
The reflector port of a mirroring group cannot be a member port of another
existing mirroring group, a fabric port (only the Switch 5500/5500G have this
limitation), a member port of an aggregation group, or a port enabled with
LACP or STP. It must be an Access port and cannot be configured with
functions like VLAN-VPN, port loopback detection, packet filtering, QoS, port
security, and so on.
existing mirroring group, a fabric port (only the Switch 5500/5500G have this
limitation), a member port of an aggregation group, or a port enabled with
LACP or STP. It must be an Access port and cannot be configured with
functions like VLAN-VPN, port loopback detection, packet filtering, QoS, port
security, and so on.
■
You cannot modify the duplex mode, port rate, and MDI attribute of a reflector
port.
port.
■
Only an existing static VLAN can be configured as the remote-probe VLAN. To
remove a remote-probe VLAN, you need to restore it to a normal VLAN first. A
remote port mirroring group becomes invalid if the corresponding
remote-probe VLAN is removed.
remove a remote-probe VLAN, you need to restore it to a normal VLAN first. A
remote port mirroring group becomes invalid if the corresponding
remote-probe VLAN is removed.
■
Do not configure the default VLAN, management VLAN or dynamic VLAN as
the remote-probe VLAN.
the remote-probe VLAN.
■
Configure all ports connecting the devices in the remote-probe VLAN as Trunk
ports, and ensure the Layer 2 connectivity from the source switch to the
destination switch over the remote-probe VLAN.
ports, and ensure the Layer 2 connectivity from the source switch to the
destination switch over the remote-probe VLAN.
■
Do not configure a Layer 3 interface for the remote-probe VLAN, run other
protocol packets, or carry other service packets on the remote-prove VLAN and
do not use the remote-prove VLAN as the voice VLAN and protocol-based
VLAN; otherwise, remote port mirroring may be affected.
protocol packets, or carry other service packets on the remote-prove VLAN and
do not use the remote-prove VLAN as the voice VLAN and protocol-based
VLAN; otherwise, remote port mirroring may be affected.
■
Do not configure a port connecting the intermediate switch or destination
switch as the mirroring source port. Otherwise, traffic disorder may occur in the
network.
switch as the mirroring source port. Otherwise, traffic disorder may occur in the
network.
■
If the intermediate or destination switch is a Switch 5500/5500G, the
bidirectional mirroring (the both keyword) function is not available.
bidirectional mirroring (the both keyword) function is not available.
■
The Switch 4210do not support the both keyword configuration.
Note the following when configuring the destination switch:
■
Packets sent from the switch CPU cannot be mirrored.