Panasonic W1014HM0-YI 用户手册
– 36 –
Chapter 4 Video Recording and Color Grading — P2 card
P2 card
Inserting a P2 card
When using the camera for the first time, be sure to set the time data beforehand. (page 31)
Insert the expressP2 memory card into the main slot and the microP2 memory card into the sub slot.
Insert the expressP2 memory card into the main slot and the microP2 memory card into the sub slot.
Main slot card access LED
Sub slot 4
Main slot 1
Main slot 2
Sub slot card access LED
Sub slot 3
Card slot cover
Fig. 1
Fig. 2
Fig. 3
Main slot lock switch
Eject button
1
Open the card slot cover. (Fig. 1)
2
Insert a card into the card slot. (Fig. 2)
f
expressP2 memory cards (main slot)
- Slide the main slot lock switch to the left to release the lock.
- Insert the card with the logo facing up until the eject button pops out.
- Press the eject button that pops up to the right.
- Slide the main slot lock switch to the right to lock.
- Slide the main slot lock switch to the left to release the lock.
- Insert the card with the logo facing up until the eject button pops out.
- Press the eject button that pops up to the right.
- Slide the main slot lock switch to the right to lock.
f
microP2 memory cards (sub slot)
- Insert with the label facing up.
- Insert with the label facing up.
3
When two P2 cards are inserted in the card slots, the P2 card with the smaller slot number will be recorded to first. Note, however, that regardless of
the slot number, if a P2 card is inserted later, that P2 card will not be accessed until the previously inserted P2 card has been recorded to.
the slot number, if a P2 card is inserted later, that P2 card will not be accessed until the previously inserted P2 card has been recorded to.
f
Example: When expressP2 memory cards are inserted in two slots
If expressP2 memory cards are inserted into the two slots, the cards are used as expressP2 memory cards in the order of the slot number 1 → 2.
However, if you remove the expressP2 memory card from slot 1 and then insert it again, recording to the expressP2 memory cards will take place
in the order slot 2 → 1.
If expressP2 memory cards are inserted into the two slots, the cards are used as expressP2 memory cards in the order of the slot number 1 → 2.
However, if you remove the expressP2 memory card from slot 1 and then insert it again, recording to the expressP2 memory cards will take place
in the order slot 2 → 1.
The P2 memory card number to be recorded to is maintained even if the camera is turned off. When the camera is next turned on, recording can be
continued to the same P2 memory card as before the camera was turned off.
continued to the same P2 memory card as before the camera was turned off.
4
Close the cover of the main slot or sub slot.
@
@
NOTE
t The topmost slot on the sub slot side is for the SD memory card used for configuration, etc. Videos and other forms of data cannot be recorded.
t Be sure to close the card slot cover in order to prevent dropping, dust, and static electricity.
t Be sure to format P2 cards only on the camera.
t Operation is not guaranteed if SDHC/SDXC memory cards other than microP2 memory cards are used in the sub slot.
t If a microP2 memory card is inserted slowly, [FORMAT ERROR!] or [NOT SUPPORTED!] may be displayed. In such a case, insert the card again.
t Be sure to close the card slot cover in order to prevent dropping, dust, and static electricity.
t Be sure to format P2 cards only on the camera.
t Operation is not guaranteed if SDHC/SDXC memory cards other than microP2 memory cards are used in the sub slot.
t If a microP2 memory card is inserted slowly, [FORMAT ERROR!] or [NOT SUPPORTED!] may be displayed. In such a case, insert the card again.