Dacor PF36 产品宣传页

Web: http://www.Dacor.com

Corporate Phone: 800-793-0093

Specifications are subject to change without notice.

See installation instructions for additional details.

1/2

◊

The depth from the front of the door (w/o door handles) to

the back of the refrigerator chassis is 26 7/8” (683 mm).

◊

The depth of the cabinet less the door is 24 1/8” (613 mm).

◊

The power cord is 60” (1524 mm) long.

◊

The height from the top of the refrigerator to the floor with

the leveling legs in the down position is 70 1/8” (1781 mm)

◊

The height from the top of the refrigerator to the floor with

the leveling legs in the fully extended position is 71 1/4”

(1810 mm) at the front of the unit and 70 11/16” (1796 mm)

at the rear of the unit.

◊

The refrigerator width from edge to edge is 35 5/8” (905

mm).

The area to the left and the right of the appliance must permit

both doors to open to a minimum of 90°. Allow a minimum of

2 1/2” (64 mm) space between the side of the refrigerator doors

and a corner wall.

70 ½” Min.

(1791 mm)

30”.

(762 mm)

Water Valve Location - Approximate Dimensions

24” (610 mm)

36” Min. (914 mm)

16”

(406 mm)

◊

A grounded three prong non-GFCI electrical outlet must

be provided and should be in a location that allows the

refrigerator to be connected without an extension cord. See

“Electrical Requirements” for additional information.

◊

The plumbing for the water line can come through the floor

flush to or from the back wall. Install the water valve in a

location that allows it to be turned off without moving the

refrigerator out in the event the refrigerator or water line

requires service.

◊

For model IF36, see document 100504 for instructions on

planning and installing integrated front panels. It is available

at www.Dacor.com.

◊

All installations must meet local plumbing code requirements.

◊

Use 1/4” (6 mm) copper line to connect the refrigerator to the

house cold fresh water supply.

◊

Install a shut off valve between the refrigerator and water

supply. The shut off valve should be a drilled saddle valve.

See the diagram above for recommended location.

◊

Do not use a piecing type or 3/16” (4.76 mm) saddle valve

which will reduce water flow and clog more easily.

◊

Allow a minimum of 24” (610 mm) diameter service loop of

copper tubing outside the wall or floor for easy connection to

the water supply.

Connect the ice maker to a cold water line with water pressure

between 35 and 120 psi. If you have any questions about your

water pressure, call your utility company.

Reverse osmosis water supply
IMPORTANT: The pressure of the water supply coming out of

a reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and 827

kPa).
If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than 40

to 60 psi (276 to 414 kPa):
■  Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■

Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■  If your refrigerator has a water filter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water

Filtration System.”

If you have questions about your water pressure, call a licensed,

qualified plumber.

Revised

11/13/07