Ingersoll-Rand QS1T 用户手册

30

P7440 Edition 10

Each time a Series QS Screwdriver is disassembled for 

maintenance and repair or replacement of parts, lubricate 

the tool as follows:
1.

Coat all exposed gears with Ingersoll-Rand No. 67 

Grease and work some of the Grease into the gearing 

of the Spindle Assembly (42).

2.

Work approximately 6 to 8 cc of Ingersoll-Rand No. 

28 Grease into the ball pockets, jaws, adjusting nut 

lock and shaft threads of the clutch mechanism.

3.

Use Ingersoll-Rand No. 10 Oil to lubricate the motor.  

Inject approximately 1 to 2 cc of oil into the air inlet 

before attaching the air hose to the tool.

In addition to adjustable clutches for controlling torque, 

Series QS Lever Inline Screwdrivers are furnished with the 

ability to precisely control speed, within certain ranges. 

Setting the speed requires a tachometer. 

Therefore, the adjustment, although simple, should only be 

attempted by a competent technician using the proper 

equipment.
The Back Cap (6) has a small, molded stud on the end face 

of the Cap nearest the Exhaust Diffuser (15). That stud 

controls the radial location of the Diffuser which controls 

the opening size of the exhaust ports. Take an initial 

reading of the tool speed by applying a tachometer with a 

convex tip to the inside of the Bit Holder (84). Using the 

procedure required to activate the motor of your particular 

model tool, bring the motor to maximum free speed.
After determining the actual velocity, shut off the air 

supply and disconnect the air line. Use a 3/4” wrench to 

loosen the Inlet Bushing. The longest slot in the Exhaust 

Diffuser will contain the molded stud on the Back Cap. 

Rotate the Diffuser to open the exhaust ports to increase 

speed or rotate it to restrict the exhaust to reduce speed. 

Being careful not to allow the Diffuser to damage the 

molded stud, tighten the Inlet Bushing to 15 ft-lbs. (20 

Nm) torque. Connect the air line and restore the air supply 

and check the velocity again. Determine which direction 

you need to rotate the Diffuser to obtain the desired speed 

and then rotate it accordingly. Best results are achieved by 

using gradual increments and frequent tachometer 

readings. Be sure to turn off the air supply and disconnect 

the line when making adjustments.

All Series QS 

Inline

Screwdrivers

2800

1.7 to 9.7 in-lbs.

(0.19 to 1.1 Nm)

--------------------

--------------------

--------------------

--------------------

2000

1.7 to 9.7 in-lbs.

(0.19 to 1.1 Nm)

7.9 to 22.1 in-lbs.

(0.89 to 2.50 Nm)

--------------------

--------------------

1710

1.7 to 9.7 in-lbs.

(0.19 to 1.1 Nm)

7.9 to 27.3 in-lbs.

(0.89 to 3.08 Nm)

--------------------

--------------------

1000

1.7 to 9.7 in-lbs.

(0.19 to 1.1 Nm)

7.9 to 27.3 in-lbs.

(0.89 to 3.08 Nm)

13.3 to 40.0 in-lbs.

(1.50 to 4.52 Nm)

500

1.7 to 9.7 in-lbs.

(0.19 to 1.1 Nm)

7.9 to 28.3 in-lbs.

(0.89 to 3.20 Nm)

13.3 to 47.8 in-lbs.

(1.50 to 5.40 Nm)

250

1.7 to 9.7 in-lbs.

(0.19 to 1.1 Nm)

7.9 to 28.3 in-lbs.

(0.89 to 3.20 Nm)

13.3 to 47.8 in-lbs.

(1.50 to 5.40 Nm)