Delta 36-5000 用户手册

7

Kickbacks can cause serious injury. A kickback occurs 

when a part of the workpiece binds between the saw 

blade and the rip fence, or other fixed object, and 

rises from the table and is thrown toward the operator. 

Kickbacks can be avoided by attention to the following 

conditions. 

•  Be certain that the rip fence is parallel to the saw 

blade.

•  DO NOT rip by applying the feed force to the section 

of the workpiece that will become the cut-off (free) 

piece. Feed force when ripping should always be 

applied between the saw blade and the fence; use a 

push stick for narrow work, 6 inches (152 mm) wide or 

less.

•  Keep saw blade guard, riving knife and anti-

kickback assembly in place and operating properly. 

The riving knife must be in alignment with the saw 

blade and the anti-kickback assembly must stop 

a kickback once it has started. Check their action 

before ripping by pushing the wood under the anti-

kickback assembly. The teeth must prevent the 

wood from being pulled toward the front of the saw. 

If any part of assembly is not operational, return to 

the nearest authorized service center for repair.

•  Plastic and composite materials (like hardboard) may 

be cut on your saw. However, since these are usually 

quite hard and slippery, the anti-kickback pawls may 

not stop a kickback. Therefore, be especially attentive 

to following proper set up and cutting procedures for 

ripping.

•  Use saw blade guard, anti-kickback pawls, and riving 

knife assembly for every possible operation, including 

all through-cut sawing.

•  Push the workpiece past the saw blade prior to 

releasing control.

•  NEVER rip a workpiece that is twisted or warped, 

or does not have a straight edge to guide along the 

fence.

•  NEVER saw a large workpiece that cannot be 

controlled.

•  NEVER use the fence as a guide or length stop when 

crosscutting.

•  NEVER saw a workpiece with loose knots, flaws, nails 

or other foreign objects.

•  NEVER rip a workpiece shorter than 10 inches (254 

mm).

•  NEVER use a dull blade. A dull blade should be 

replaced or re-sharpened.

This saw is equipped with a 15-amp motor for use with 

a 120-volt, 60-HZ alternating current. It can be re-wired 

for use with a 240-volt power source by a qualified 

electrician. See instructions below regarding proper 

connections for your saw as wired. 
For voltage, the wiring in a shop is as important as 

the motor’s rating. A line intended only for lights may 

not be able to properly carry the current needed for a 

power tool motor; wire that is heavy enough for a short 

distance may be too light for a greater distance; and a 

line that can support one power tool may not be able to 

support two or three. 

A separate electrical circuit should be used for your 

machines. This circuit should not be less than #12 

wire and should be protected with a 20-amp time lag 

fuse. If an extension cord is used, use only 3-wire 

extension cords which have 3-prong grounding-type 

plugs and matching receptacle which will accept the 

machine’s plug. Before connecting the machine to the 

power line, make sure the switch (s) is in the “OFF” 

position and be sure that the electric current is of the 

same characteristics as indicated on the machine. A 

substantial voltage drop will cause a loss of power and 

overheat the motor. It may also damage the machine. 

In the event of a malfunction or breakdown, grounding 

provides a path of least resistance for electric current 

to reduce the risk of electric shock. This machine is 

equipped with an electric cord having a grounding 

conductor and a grounding plug. The plug must be 

plugged into a matching receptacle that is properly 

installed and grounded in accordance with all local 

codes and ordinances.
Do not modify the plug as provided on your saw 

or as rewired by your electrician. If it will not fit the 

receptacle, have the proper receptacle installed by a 

qualified electrician. 
Improper connection of the equipment-grounding 

conductor can result in risk of electric shock. The 

conductor with insulation having an outer surface that 

is green with or without yellow stripes is the grounding 

conductor. If repair or replacement of the electric cord 

or plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.