Milwaukee 5317-59 用户手册

Setting Self-Drilling Anchors (5317-59/59A only)
MILWAUKEE Tooth Anchor Chucks require a “B” 
taper adapter.
1. Place the proper size tooth anchor chuck into 

the “B” taper adapter. Then insert the “B” taper 
adapter into the tool and lock it into place as 
described. See “Installing Bits and Chisels”. 

2. Insert the anchor 

into the tooth an-
chor chuck. Set 
the knob for ham-
mering only. Set 
the anchor on your 
mark and hammer 
until the teeth have 
penetrated the con-
crete.

3. Set the knob for 

h a m m e r i n g   w i t h 
rotation and drill un-
til the chuck is 1/8" 
above the concrete.

  NOTE: It may be 

necessary to clean 
dust and cuttings 
from the anchor 
several times while 
drilling the hole.

4. Remove the anchor 

from the hole while 
the tool is running. 
Clean the dust and 
cuttings from the 
anchor by pointing it downward and turning the 
tool on and off several times. Clean the dust out 
of the hole with a vacuum cleaner or blowout bulb.

5. Place the expan-

sion plug into the 
anchor and insert 
the anchor into the 
hole. Switch the 
knob back to ham-

1/8"

mering only, and 
hammer the anchor 
fi rmly into the hole.

6. Snap the head off 

of the anchor. To 
remove the head of 
anchors up to 5/8", 
grasp the handles 
fi rmly and pull the 
t o o l   s h a r p l y   t o -
wards you or snap 
off the anchor head with a hand hammer as 
shown. The anchor is now ready to receive a 
bolt.

7. To remove the anchor head wedged in the tooth 

anchor chuck, use drift pin 48-86-0100. 

8. To remove the tooth anchor chuck, remove the 

“B” taper adapter from the nose of the tool. Insert 
the drift pin supplied with the adapter into the 
hole on the side of the “B” taper adapter and 
strike it sharply to force out the tooth anchor 
chuck. 

Chiseling and Chipping
MILWAUKEE Rotary Hammers may be used for 
chipping and chiseling. 
When chiseling, hold the tool at an angle to the 
workpiece. Work from a corner or close to the edge 
of the workpiece, breaking off one small area at a 
time rather than attempting too large an area. 
A variety of accessories are available.

Scaling Chisels
For removing weld spatter or 
scale and cutting straight lines.

Bushing Tools
Used to surface concrete.

Mortar Cutting Chisels 
(Seam Tools)
For removing old mortar for tuck 
pointing or caulking.

Bull Points
For demolition work and starting 
holes in concrete slabs.

Flat Chisels
For edging, chipping or 
channeling.

Slotting Chisel
For slotting and cutting between 
drilled holes in concrete and 
masonry.

Maintaining Tools
Keep your tool in good repair by adopting a regular 
maintenance program. Before use, examine the gen-
eral condition of your tool. Inspect guards, switches, 
tool cord set and extension cord for damage. Check 
for loose screws, misalignment, binding of moving 
parts, improper mounting, broken parts and any 
other condition that may affect its safe operation. If 
abnormal noise or vibration occurs, turn the tool off 
immediately and have the problem corrected before 
further use. Do not use a damaged tool. Tag damaged 
tools “DO NOT USE” until repaired (see “Repairs”).
Under normal conditions, relubrication is not neces-
sary until the motor brushes need to be replaced. 
After six months to one year, depending on use, 
return your tool to the nearest MILWAUKEE service 
facility for the following:
• Lubrication
• Brush inspection and replacement
• Mechanical inspection and cleaning (gears, 

spindles, bearings, housing, etc.)

• Electrical inspection (switch, cord, armature, etc.)
• Testing to assure proper mechanical and electrical 

operation

Cleaning
Clean dust and debris from vents. Keep the tool 
handles clean, dry and free of oil or grease. Use 
only mild soap and a damp cloth to clean your tool 
since certain cleaning agents and solvents are 
harmful to plastics and other insulated parts. Some 
of these include: gasoline, turpentine, lacquer thin-
ner, paint thinner, chlorinated cleaning solvents, 
ammonia and household detergents containing 
ammonia. Never use fl ammable or combustible 
solvents around tools.

Repairs
If your tool is damaged, return the entire tool to the 
nearest service center.

injury, always unplug your tool before 
performing any maintenance. Never disas-
semble the tool or try to do any rewiring 
on the tool’s electrical system. Contact a 
MILWAUKEE service facility for ALL repairs.

For a complete listing of accessories refer to your 
MILWAUKEE  Electric Tool catalog or go on-line 
to www.milwaukeetool.com. To obtain a catalog, 
contact your local distributor or a service center.