Wagner SprayTech HIGH PERFORMANCE AIRLESS SPRAYER 用户手册
© 2003 Wagner Spray Tech - All rights reserved.
5
Customer Service: 800-328-8251
English
L
OCKING AND UNLOCKING THE GUN
Always lock the trigger off when attaching the spray tip or
when the spray gun is not in use.
when the spray gun is not in use.
P
LUGGING IN THE SPRAYER
1. Check that the ON/OFF
switch is in the OFF
postion.
postion.
2. Plug the sprayer into a
heavy duty grounded
extension cord (refer to
Important Electrical
Information, page 3).
extension cord (refer to
Important Electrical
Information, page 3).
P
RESSURE RELIEF PROCEDURE
Be sure to follow the pressure relief procedure when
shutting the unit off FOR ANY PURPOSE. This procedure is
used to relieve pressure from the spray hose.
shutting the unit off FOR ANY PURPOSE. This procedure is
used to relieve pressure from the spray hose.
1. Lock the spray gun off and
flip the ON/OFF switch to
the OFF position.
the OFF position.
2. Turn the PRIME/SPRAY
knob to PRIME.
3. Unlock the spray gun and
then trigger it onto a scrap
piece of wood or cardboard.
piece of wood or cardboard.
4. Lock the spray gun.
SPR
A
Y
PRIME
O
WARNING
O
The spray tip SHOULD NOT be attached until after the
sprayer and spray hose has been purged and primed.
sprayer and spray hose has been purged and primed.
U
NLOCKING THE GUN
To unlock the gun, turn the
trigger lock to be in line with
the trigger.
trigger lock to be in line with
the trigger.
L
OCKING THE GUN
The gun is secured when
the trigger lock is at a 90°
angle (perpendicular) to the
trigger in either direction.
the trigger lock is at a 90°
angle (perpendicular) to the
trigger in either direction.
WARNING
E
MPTYING THE
H
OPPER
1. Perform all the steps of the Pressure Relief Procedure (page 5).
2. Remove the lid from the hopper.
3. Grab top handle of the sprayer with one hand, grab rear
3. Grab top handle of the sprayer with one hand, grab rear
handle with the other.
4. Lift and tilt the sprayer so that material will pour from one of
the front corners of the hopper and into its original container.
P
AINT
S
TRAINING
It is recommended that in order to avoid premature tip and filter
clogging you should strain your paint before spraying. Follow
manufacturer’s recommendations.
clogging you should strain your paint before spraying. Follow
manufacturer’s recommendations.
C
HOOSING THE
C
ORRECT
S
PRAY
G
UN
F
ILTER
Use the proper gun filter based on the tip size being used.
Part No.
Tip Size
Filter
Type
Type
Mesh
Number
Number
Qty.
Color of
Filter
Body
0154918
.011
Extrafine
180 mesh
0.084 mm
red
2 pack
2 pack
0154675
.013 - .015 Fine
100 mesh
0.140 mm
yellow
Make sure your floors and
furnishings are protected
with drop cloths to avoid
property damage.
The unit, when filled with
spraying material, can be
heavy. Make sure to lift
with your legs and not your
back in order to reduce the
risk of injury.
CAUTION
WARNING
Front
corners
Top
handle
Rear
handle
handle
O
Follow these instructions if the hopper is filled with material
and 1) your sprayer malfunctions or 2) you finish your
spraying project without using all the material in the hopper.
and 1) your sprayer malfunctions or 2) you finish your
spraying project without using all the material in the hopper.
B
EFORE YOU
B
EGIN
--
T
HIS PAGE CONTAINS INFORMATION THAT WILL BE
REPEATED THROUGHOUT THE MANUAL
.