Bostitch BTFP71875 用户手册
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints
• crystalline silica from bricks and cement and other masonry products
• arsenic and chromium from chemically-treated lumber
known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints
• crystalline silica from bricks and cement and other masonry products
• arsenic and chromium from chemically-treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
AIR SUPPLY AND CONNECTIONS
Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly
causing injury.
causing injury.
Do not use supply sources which can potentially exceed 200 PSI as tool may burst, possibly causing injury.
The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can
remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected
possibly causing injury.
remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected
possibly causing injury.
Do not pull trigger while connected to the air supply as the tool may cycle, possibly causing injury.
Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When
tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury; 6.)
Before placing tool on any surface, hanging tool on belt, or otherwise temporarily suspending use of the tool.
tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury; 6.)
Before placing tool on any surface, hanging tool on belt, or otherwise temporarily suspending use of the tool.
OPERATION
Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull or grasp the secondary trigger unless nose
is directed toward the work; 3.) Keep others a safe distance from the tool while tool is in operation as accidental actuation
may occur, possibly causing injury.
is directed toward the work; 3.) Keep others a safe distance from the tool while tool is in operation as accidental actuation
may occur, possibly causing injury.
The operator must not hold the secondary trigger pulled except during fastening operation as serious injury could result
if the trigger accidentally contacts someone or something, causing the tool to cycle.
if the trigger accidentally contacts someone or something, causing the tool to cycle.
Keep hands and body away from the discharge area of the tool.
Check operation of the secondary trigger mechanism frequently. Do not use the tool if the secondary trigger is not working
correctly as accidental actuation of a fastener may result. Do not interfere with the proper operation of the secondary
trigger mechanism.
correctly as accidental actuation of a fastener may result. Do not interfere with the proper operation of the secondary
trigger mechanism.
Never inadvertently pull or grasp the secondary trigger when moving about, changing work location, when holstering or
hanging tool, or when preparing work surface for fastening operation.
hanging tool, or when preparing work surface for fastening operation.
Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of
fasteners which could cause injury.
fasteners which could cause injury.
Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected
possibly causing injury.
possibly causing injury.
This stapler produces SPARKS during operation. NEVER use the stapler near flammable substances, gases or vapors including
lacquer, paint, benzine, thinner, gasoline, adhesives, mastics, glues or any other material that is -- or the vapors, fumes or
byproducts of which are -- flammable, combustible or explosive. Using the stapler in any such environment could cause an
EXPLOSION resulting in personal injury or death to user and bystanders. damage.
lacquer, paint, benzine, thinner, gasoline, adhesives, mastics, glues or any other material that is -- or the vapors, fumes or
byproducts of which are -- flammable, combustible or explosive. Using the stapler in any such environment could cause an
EXPLOSION resulting in personal injury or death to user and bystanders. damage.
MAINTAINING THE TOOL
When working on air tools note the warnings in this manual and use extra care when evaluating problem tools.
TOOL SPECIFICATIONS
FASTENER SPECIFICATIONS:
TOOL AIR FITTING:
This tool uses a free-flow connector plug, 1/4” N.P.T. The minimum inside diameter should be .200” (5mm). The fitting must be capable of discharging
tool air pressure when disconnected from the air supply.
OPERATING PRESSURE:
80 to 100 PSI (5.5 to 6.9 bars). Select the operating pressure within this range for best fastener performance. DO NOT EXCEED THE RECOMMENDED
OPERATING PRESSURE.
OPERATING PRESSURE.
-3-
MODEL
LENGTH
HEIGHT
WIDTH
WEIGHT
BTFP71875
8.55” (217 mm)
6.98” (177 mm)
1.73” (44 mm)
2.3 lb (1.1 kg)
MODEL
FASTENER SERIES:
FASTENER RANGE:
FASTENER TYPE:
BTFP71875
TRA700 Series
1/4" - 9/16" (6mm -14mm)
3/8” Crown
SWKBN Series
12mm -15mm (1/2" - 5/8")
18 Gauge