Husqvarna 232R 用户手册
16 –
English
ASSEMBLY
•
Place the cover (I) and the support flange (F) on the
output shaft.
output shaft.
•
Fit the nut (G). Tighten the nut to a torque of 35-50 Nm
(3.5-5 kpm). Use the socket spanner in the tool kit. Grasp
the handle of the spanner as close to the trimmer guard
as possible. To tighten the nut, turn the spanner in the
opposite direction to the direction of rotation (Caution! left-
hand thread).
(3.5-5 kpm). Use the socket spanner in the tool kit. Grasp
the handle of the spanner as close to the trimmer guard
as possible. To tighten the nut, turn the spanner in the
opposite direction to the direction of rotation (Caution! left-
hand thread).
•
Fit the bottom half of the trimmer head (K) to the cover (I)
by pressing them together, with the cut-outs on the bottom
half aligned with the catches on the cover.
by pressing them together, with the cut-outs on the bottom
half aligned with the catches on the cover.
•
To dismantle, follow the instructions in the reverse order.
Fitting the trimmer guard and
trimmer head Trimmy SII (235R,
235FR)
trimmer head Trimmy SII (235R,
235FR)
•
Fit the correct trimmer guard (A) for use with the trimmer
head. CAUTION! Ensure that the guard extension is
fitted.
head. CAUTION! Ensure that the guard extension is
fitted.
Hang the trimmer guard/combination guard (A) on the two
hooks on the plate holder (M). Bend the guard around the
shaft and tighten it with the bolt (L) on the opposite side of
the shaft. Use the locking pin (C). Place the locking pin in
the groove on the screw head and tighten. See diagram.
hooks on the plate holder (M). Bend the guard around the
shaft and tighten it with the bolt (L) on the opposite side of
the shaft. Use the locking pin (C). Place the locking pin in
the groove on the screw head and tighten. See diagram.
•
Fit the drive disc (B) on the output shaft.
•
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
Screw on the trimmer head (H) in the opposite direction to
the direction of rotation.
the direction of rotation.
•
Tighten the trimmer head to a torque of 35-50 Nm (3.5-5
kpm).
kpm).
•
To dismantle, follow the instructions in the reverse order.
Fitting other guards and cutting
attachments (232R)
attachments (232R)
•
Fit the trimmer guard/combination guard (A) intended for
use with the trimmer head/plastic blades. Secure the
trimmer guard/combination guard using four screws (L)
and the support plate (M) as shown.
use with the trimmer head/plastic blades. Secure the
trimmer guard/combination guard using four screws (L)
and the support plate (M) as shown.
•
Fit the drive disc (B) on the output shaft.
•
Turn the blade shaft until one of the holes in the drive disc
aligns with the corresponding hole in the gear housing.
aligns with the corresponding hole in the gear housing.
•
Insert the locking pin (C) in the hole to lock the shaft.
•
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
opposite direction to the direction of rotation.
Fitting other guards and cutting
attachments (235R, 235FR)
attachments (235R, 235FR)
•
Fit the trimmer guard/combination guard (A) intended for
use with the trimmer head/plastic blades. CAUTION!
Ensure that the guard extension is fitted.
use with the trimmer head/plastic blades. CAUTION!
Ensure that the guard extension is fitted.
B
A
M
L
H
A
L
C
M
H
B
A
L
M
C
H
H