Emerson h990 用户手册
HOW TO USE THIS INSTRUCTION MANUAL
Provides a step-by-step narrative describing the installation step, with check boxes that
can be marked as you progress through the installation.
can be marked as you progress through the installation.
Contains simple illustrations that provide visual instruction to support the narrative.
CAUTIONS, WARNINGS and DANGERS that will require your attention during the step.
These instructions are separated into main sections, indicated by numbers, and subsections,
indicated by capital letters. The manual is setup this way to allow you to take a break at any
point after completing a section or subsection without affecting the installation process.
indicated by capital letters. The manual is setup this way to allow you to take a break at any
point after completing a section or subsection without affecting the installation process.
What you’ll see in the
instruction manual:
instruction manual:
1
2
3
OVERVIEW OF A
COMPLETED SETUP
H990-SS
H770-SS
H-View-SS
H-Wave-SS
HC-View-SS
HC-Wave-SS
Identify the model of your instant hot water dispenser and record it here:________________
A
Property Damage: Do not pinch or break copper
tubing. Do not distort the last 1 inch of tubing.
INSTALLING THE FAUCET - View/Wave
Unpack dispenser components.
On a firm, flat surface, carefully
straighten the copper tubing.
straighten the copper tubing.
Remove the wing nut from
the valve body.
the valve body.
View / Wave
1
2
An imminently hazardous situation, which, if not avoided, will result in death or serious injury.
A potentially hazardous situation, which, if not avoided, could result in death or serious injury.
A potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
3
Equipment You May Need:
We are delighted that you have chosen the InSinkErator
®
Instant Hot Water Dispenser to be a part of
your home. This unique appliance will save you time and effort in the kitchen, and you’ll enjoy
discovering new uses for it each day. That’s exactly why millions of people are now using an
InSinkErator Instant Hot Water Dispenser.
discovering new uses for it each day. That’s exactly why millions of people are now using an
InSinkErator Instant Hot Water Dispenser.
We are confident that by following our step-by-step instructions, you’ll soon be enjoying the
convenience of instant hot water.
convenience of instant hot water.
For your satisfaction and safety, read all instructions, cautions, warnings and dangers before installing or using this
instant hot water dispenser.
instant hot water dispenser.
This particular unit is not intended for commercial use.
Make sure that all electrical wiring and connections conform to local codes.
A standard 120-volt grounded electrical outlet is required under the sink for the dispenser’s electrical power.
The wall outlet powering your dispenser must have power supplied to it continuously.
This outlet must be fused and should not be controlled by the same wall switch that operates the disposer, unless you
have a SinkTop Switch
have a SinkTop Switch
™
from InSinkErator
®
.
It is recommended that a dedicated control valve be installed on the cold water line supplying water to this system.
If you suspect elevated levels of chlorine in your water, or your water has a rusty appearance before the installation
of this unit, it is recommended to use our water filtration system.
of this unit, it is recommended to use our water filtration system.
This product contains stainless steel. The manufacturer cannot guarantee against rusty water because of the
number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty
water discharged from the hot water dispenser may indicate the need for service or replacement of this product.
number of factors that are involved beyond the manufacturer’s control. However, the sudden appearance of rusty
water discharged from the hot water dispenser may indicate the need for service or replacement of this product.
The use of a water filter should NOT result in the water pressure to drop below 30 psi (207kPa).
If it does, this will prevent your unit from operating properly.
If it does, this will prevent your unit from operating properly.
Moving parts inside the tank causing a rattling noise is normal.
WHAT YOU SHOULD KNOW BEFORE YOU BEGIN
Equipment Required:
Drill
T-fitting
Dedicated control valve
Adjustable wrench
Phillips and flat blade screwdrivers
Pencil
Tape measure
Level
Anchors for drywall
Hole saw
Basin wrench
Hole punch
If you intend to use the sprayer hole in your sink for your dispenser, you may need a basin wrench and a
1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line.
1/8" plug or a 1/4" cap (not supplied) for the faucet spray hose line.
See Step 1-B.
If you need to cut a mounting hole in your stainless steel sink, you may need a 1
1
⁄
4
" - 1
1
⁄
2
" hole saw made
for cutting stainless steel or a hole punch. Consult a professional if you are drilling into a surface other
than stainless steel.
than stainless steel.
WHAT YOU NEED TO GET STARTED
2
3