Whirlpool ADG 750 用户手册
22
In order to avoid that there is more water staying in the inlet hose,
please close the hydrant after using.(For the models: no safety inlet hose.)
please close the hydrant after using.(For the models: no safety inlet hose.)
Positioning the Appliance
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the exces s water in hoses cannot be drained di rectly
into the sink. It will b e necessary to d rain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
into the sink. It will b e necessary to d rain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Water Outlet
Connect the water d rain hose. The d rain hose must b e co rrec tly fi tted to av oid wate r leaks.
En sure that the wat er inlet hose is not kinked or s quashed.
En sure that the wat er inlet hose is not kinked or s quashed.
The following things should be checked before starting the dishwasher.
Syphon Connection
The waste connection must be at a h eight of betw een 50 c m ( minimum ) and 10 0 cm (maximum )
from the bo ttom of the dish. The wate r drain hose should be fixed by a hose clip.
from the bo ttom of the dish. The wate r drain hose should be fixed by a hose clip.
Start of Dishwasher
The content of this manual is very helpful to the users.
After installation, please make sure to keep this manual.
Extension Hose
If you n eed a drain hose extensi on, make sure to use a similar dra in ho se.
It m ust be no longer than 4 metres; o therwise the cleanin g effect o f the dishwasher could b e re duced.
It m ust be no longer than 4 metres; o therwise the cleanin g effect o f the dishwasher could b e re duced.
1
The dishwasher is level and fixed properly
2
The inlet valve is open
3
There is a leakage at the connections of the conducts
4
The wires are tightly connected
5
The power is switched on
6
The inlet and drain hoses are knotted
7
All packing materials and printings should be taken out from the dishwasher
Connect the cold water supply hose to a threaded 3/4(inch) connector and make s ure
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inlet to be block ed and damage the appliance.
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inlet to be block ed and damage the appliance.
The water supply to the appliance can also be connected to the household hot water
line (such as, central system, heating system),as long as it does not exceed a
temperature of 60 C. In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as
described in the section for the connection to the cold water line.
line (such as, central system, heating system),as long as it does not exceed a
temperature of 60 C. In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as
described in the section for the connection to the cold water line.
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate pro per installation.
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate pro per installation.