Delta Electronics SIG110H 用户手册

                                                                                                                   

Motion Model: SIG80M 

Factory setting: low speed airflow 40CFM, time delay 15 minutes.

 

Humidity Model: SIG110H 

 

 

5-2. Motion control mode: Turn the POWER switch on to operate at 

motion control mode. When motion is detected, the fan will run at 

full speed  and the LED indicator will be amber. When motion is 

not detected, the fan will continue to run at the full speed until 

the user -adjustable time delay has elapsed, and then will 

automatically change to the user-adjustable low speed airflow. 

The LED indicator will be green.

5-3. Humidity control mode: Turn the POWER switch on to operate 

at humidity control mode - the LED indicator will be blue. When 

the ambient humidity is higher than the user -adjustable set-point, 

the fan will run at full speed. When the ambient humidity is lower 

than the set-point, the fan will continue to run at the full speed 

until a 10-minute time delay has elapsed, and then will auto 

matically change to the user-adjustable low speed airflow.

 

5-4. Full speed mode: Turn the MODE switch on to operate at full 

speed mode - the LED indicator will be amber. 

 

5-5. Humidity tolerance is about ±10%. Long -time operation will 

influence the detecting precision as dust accumulates. The 

humidity switch may need to be adjusted. 

 

Factory setting: low speed airflow 60CFM, humidity 60%RH

 

Disconnect the power source before working on the unit. Routine 

maintenance must be done every year. 

CAUTION: 

1. Never use gasoline, benzene, thinner or any other such chemi-

cals to clean the ventilating fan. 

2. Do not allow water to enter the mot or

3. Do not soak resin parts in water over 60°C (140°F)

CLEANING 

1. Pull down the springs to remove the grille. 

2. Wash and clean the grille. (Use non -abrasive kitchen detergent 

and wipe dry with a new cloth.) 

3. Remove dust and dirt from the ventilating fan

4. Using a cloth dampened with non -abrasive kitchen detergent, 

remove any dirt from ventilating fan. Wipe dry with a new cloth

5. Replace the grille

 

DELTA ELECTRONICS THREE YEAR LIMITED WARRANTY

    Delta Electronics Inc. (“Delta Electronics”) warrants to the 

original consumer purchaser in the USA that the Breez 

ventilation fan products will be free from defects in material or 

workmanship. This warranty is limited to three (3) years from 

the original date of purchase.

Limitations and Exclusions 

1. During the warranty period, a replacement for any defective 

product will be supplied free of charge for installation by the 

consumer. The warranty provided herein does not cover 

charges for labor or other costs incurred in the troubleshooting, 

repair, removal, and installation service.

2. All returns of defective parts or products must include the 

product model number, and must be made through an 

authorized Delta Electronics distributor. Authorized returns 

must be shipped prepaid. Repaired or replacement products 

will be shipped by Delta Electronics 

F.O.B. shipping point.

3. Delta Electronics shall not be liable for any indirect, inciden-

tal, consequential, punitive, or special damages arising out of or 

in connection with products use or performance, regardless of 

the form of action whether in contract, tort (including 

negligence), strict product liability or otherwise. 

4. This warranty does not extend to uorescent lamp starters 

and tubes.

5. The warranty does not cover if user does not comply with 

manufacturer’s installation manual.

6. To qualify for warranty service, you must notify Delta 

Electronics at the address or telephone number below.

7. Delta Electronics shall have no liability to the original 

owner-user with respect to any defect caused by abuse, misuse, 

neglect, improper transportation or storage, improper testing, 

improper installation, improper operation, improper use, 

improper maintenance, improper repair, improper alteration, 

improper modifcation, tampering or accident of products or 

parts thereof, or unusual deterioration or degradation of 

products or parts thereof due to a physical environment 

beyond the requirements of products’ specifcations.

Address: 4405 Cushing Parkway, Fremont, CA 94538

US Toll Free Number: 1-888-979-9889

Note: Design and specifications subject to change without notice.