Samsung RF4267HA 用户手册
06_
setting up
• Do not locate the refrigerator where it may become
wet.
When moving your refrigerator
To prevent floor damage, be sure the front
adjusting legs are in the up position (above
the floor).
adjusting legs are in the up position (above
the floor).
Refer to ‘Adjusting the doors’ in the manual (on
page 9).
page 9).
FLOORING
For proper installation, you must place this refrigerator
on a level, hard surface that is the same height as the
rest of the floor. This surface should be strong enough
to support a fully loaded refrigerator, or approximately
359lbs (165kg). To protect the finish of the flooring, cut
a large section of the cardboard carton and place it
under the refrigerator where you are working.
When moving the refrigerator, you need to pull and
push it straight forwards or back. Do not wiggle it from
side to side.
For proper installation, you must place this refrigerator
on a level, hard surface that is the same height as the
rest of the floor. This surface should be strong enough
to support a fully loaded refrigerator, or approximately
359lbs (165kg). To protect the finish of the flooring, cut
a large section of the cardboard carton and place it
under the refrigerator where you are working.
When moving the refrigerator, you need to pull and
push it straight forwards or back. Do not wiggle it from
side to side.
AccESSORIES AND REquIRED
TOOLS
TOOLS
The following accessories are included with your
refigerator:
refigerator:
Hex wrench
Fastener
Required Tools (Not provided)
You need the following tools to complete the
installation of your refirgerator:
installation of your refirgerator:
Philips screw-
driver (+)
Flat-blade screw-
driver (-)
Socket wrench
(10mm)
Pliers
Allen wrench (3/16”) (5mm)
REMOvING THE REFRIGERATOR
DOORS
DOORS
For some installations you need to remove the fridge
and flex doors and the freezer drawer so you can
move the refrigerator to its final location. Do not
remove the doors/drawer if you don't need to. If you
do not need to remove the doors/drawer, go to
Adjusting the Level on page 8. If you need to remove
the doors/drawer, continue below.
Before removing the door/drawer, make sure you read
the following items:
and flex doors and the freezer drawer so you can
move the refrigerator to its final location. Do not
remove the doors/drawer if you don't need to. If you
do not need to remove the doors/drawer, go to
Adjusting the Level on page 8. If you need to remove
the doors/drawer, continue below.
Before removing the door/drawer, make sure you read
the following items:
Disconnect power to the refrigerator before
removing the door or drawer.
removing the door or drawer.
• Be careful not to drop, damage or scratch
the door/drawer while removing them.
• Be careful not to get injured while removing the
door/drawer.
• Reattach the door/drawer properly to avoid:
- Moisture from air leakage.
- Uneven door alignment.
- Wasting energy due to improper door seal.
- Uneven door alignment.
- Wasting energy due to improper door seal.
Disassemble the refrigerator doors
Be careful not to drop and scratch the doors
while removing the doors.
while removing the doors.
Disassemble the refrigerator doors
1. With the door opened, remove the cap top table
(
1 ) with a flat-blade screwdriver(-). and close
the door. Remove 2 screws holding down the
cover hinge (
cover hinge (
2 ) and turn it with several wires
connected.
cAuTION
Flat-blade
screw driver(-)
screw driver(-)
control Lever
WARNING
WARNING
DA68-02481A-0.2.indb 6
2011.3.7 9:19:7 AM