Fujitsu P3AM-3842-05ENZ0 用户手册
Chapter 9 Logical Unit Recognition
>
>
9.1 Displaying the Recognized Logical Units
ETERNUS DX Disk storage systems Server Connection Guide (Fibre Channel) for Linux
32
Copyright 2010 FUJITSU LIMITED
P3AM-3842-05ENZ0
9.1.2
For SUSE Linux Enterprise Server
•
Checking for LUNs in the boot message
Open the /var/log/boot.msg file to confirm that Linux has recognized the ETERNUS DX Disk
storage systems' LUNs.
The following shows an example (Messages can be scrolled (back and forth) using the arrow
keys).
Open the /var/log/boot.msg file to confirm that Linux has recognized the ETERNUS DX Disk
storage systems' LUNs.
The following shows an example (Messages can be scrolled (back and forth) using the arrow
keys).
•
Checking for LUNs with the "cat" command
Use the "cat" command to display the "/proc/scsi/scsi" file, which contains a list of recognized
SCSI devices.
The following shows an example of this.
Use the "cat" command to display the "/proc/scsi/scsi" file, which contains a list of recognized
SCSI devices.
The following shows an example of this.
At this point the Multipath Driver has not been set up yet, so two SCSI devices are shown for
each connected LUN (i.e. if there are 3 LUNs, 6 SCSI devices are shown).
each connected LUN (i.e. if there are 3 LUNs, 6 SCSI devices are shown).
<6>qla2x00_set_info starts at address - c3600060
<6>qla2x00: Found VID-1077 DID-2422 SSVID-1077 SSDID-134
<6>scsi(2): Found a QLA2422 @ bus l, device 0xa, 1rq 29, iobase 0xf9o0d000
.
.
.
<6>scsi2 : Qlogic QLA2422 PCI to Fibre Channel Host Adapter: bus l device
10 irq 29
<4>
Firmware version: 4.00.12, Driver version 7.07.01
<4>
<6>scsi3 : Qlogic QLA2422 PCI to Fibre Channel Host Adapter: bus l device
10 irq 30
<4>
Firmware version: 4.00.12, Driver version 7.07.01
<4>
<4> Vendor: FUJITSU Model: ETERNUS_DX400
Rev: 0000
<4> Type:
Direct-Access
ANSI SCSI revision: 05
<4> Vendor: FUJITSU Model: ETERNUS_DX400
Rev: 0000
<4> Type:
Direct-Access
ANSI SCSI revision: 05
<6>scsi(2:0:0:0): Enabled tagged queuing, queue depth 20.
<6>scsi(2:0:0:1): Enabled tagged queuing, queue depth 20.
<4>Attached scsi disk sdb at scsi2, channel 0, id 0, lun 0
<4>Attached scsi disk sdb at scsi2, channel 0, id 0, lun 1
<4>SCSI device sdb: 4096000 512-byte hdwr sectors (2097 MB)
<6> sdb: unknown partition table
<4>SCSI device sdb: 4096000 512-byte hdwr sectors (2097 MB)
<6> sdb: unknown partition table
←
Driver version
←
Driver version
# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vender: FUJITSU
Model: MAP3735NC
Rev: 5207
Type:
Direct-Access
ANSI SCSI revision: 03
Host: scsi0 Channel: 00 Id: 08 Lun: 00
Vender: SDR
Model: GEM318
Rev: 0
Type:
Processor
ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 05 Lun: 00
Vender: SEAGATE
Model: DAT 9SP40-000
Rev: 9M38
Type:
Sequential-Access
ANSI SCSI revision: 03
Host: scsi2 Channel: 00 Id: 00 Lun: 00
Vender: FUJITSU
Model: ETERNUS_DX400
Rev: 0000
Type:
Direct-Access
ANSI SCSI revision: 05
Host: scsi2 Channel: 00 Id: 00 Lun: 01
Vender: FUJITSU
Model: ETERNUS_DX400
Rev: 0000
Type:
Direct-Access
ANSI SCSI revision: 05