U-Line CLRCO2175 用户手册
12
CLR2160, CLRCO2175
To defrost:
1. Turn unit off.
2. Remove all products from the interior and prop the
door in an open position (2 in. (5 cm) minimum).
3. Allow the frost to completely melt naturally. Clean the
interior and all removed components using a mild non-
abrasive detergent and warm water solution applied
with a soft sponge or non-abrasive cloth. NOTE: DO
NOT use any solvent-based or abrasive cleaners. They
will discolor or damage the interior.
abrasive detergent and warm water solution applied
with a soft sponge or non-abrasive cloth. NOTE: DO
NOT use any solvent-based or abrasive cleaners. They
will discolor or damage the interior.
4. Dampen a soft sponge or non-abrasive cloth in clean
water and wipe down the cabinet interior and removed
components to remove any detergent residue. Rinse the
sponge or cloth in clean water and repeat as necessary
until the cabinet and components are clean.
components to remove any detergent residue. Rinse the
sponge or cloth in clean water and repeat as necessary
until the cabinet and components are clean.
5. When the interior is dry, turn unit back on.
Condenser Cleaning
Interval - Every Three Months
To maintain operational efficiency, keep the front grille
free of dust and lint and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
To maintain operational efficiency, keep the front grille
free of dust and lint and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
WARNING
Disconnect electric power to the unit before
cleaning the condenser.
cleaning the condenser.
To remove and replace the grille for access to the
condenser fins, follow this procedure:
condenser fins, follow this procedure:
Figure 8
1. Disconnect electrical power to the unit.
2. Loosen two screws (Figure 8, 1) completely.
NOTE: Screws are held in the grille by o-ring retainers,
and will not come free of the grille.
and will not come free of the grille.
3. Remove the grille.
WARNING
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
fins are SHARP and can be easily damaged.
CAUTION
DO NOT use any type of cleaner on the condenser
unit.
unit.
4. Clean the condenser coil (Figure 8, 2) using a soft
brush with a “combing” action or vacuum cleaner. Do
not touch the condenser coil.
not touch the condenser coil.
5. Position the grille to align the mounting screws with
the holes in the cabinet.
6. Secure, but do not over-tighten both grille screws.
7. Reconnect power to the unit.
Clear Ice Maker Maintenance
Self-Cleaning Cycle
Interval - Every Six Months
To maintain operational efficiency, clean the unit every six
months (depending on water conditions, more or less
frequent cleaning may be necessary). If the ice maker
requires more frequent cleaning, consult a qualified
plumber to test the water quality and recommend
appropriate treatment.
To maintain operational efficiency, clean the unit every six
months (depending on water conditions, more or less
frequent cleaning may be necessary). If the ice maker
requires more frequent cleaning, consult a qualified
plumber to test the water quality and recommend
appropriate treatment.
WARNING
Wear rubber gloves and safety goggles and/or
face shield when handling Ice Machine Cleaner.
face shield when handling Ice Machine Cleaner.
CAUTION
Use only U-Line Ice Machine Cleaner (P/N 41978,
available from your dealer or direct from your local
parts distributor. To locate a parts distributor near
you, visit www.U-LineService.com.). It is a violation
of federal law to use this solution in a manner
inconsistent with its labeling. Use of any other
cleaner can ruin the finish of the evaporator and
will void the warranty. Read and understand all
labels printed on the package before use.
available from your dealer or direct from your local
parts distributor. To locate a parts distributor near
you, visit www.U-LineService.com.). It is a violation
of federal law to use this solution in a manner
inconsistent with its labeling. Use of any other
cleaner can ruin the finish of the evaporator and
will void the warranty. Read and understand all
labels printed on the package before use.
U-Line Ice Machine Cleaner is used to remove lime scale
and other mineral deposits. Refer to the following steps
to initiate the self-cleaning cycle.
and other mineral deposits. Refer to the following steps
to initiate the self-cleaning cycle.
IMPORTANT
IMPORTANT
• The Model CLRCO2175 refrigerator will not
operate during the ice maker cleaning cycle.
Remove all fresh food to prevent spoilage.
Remove all fresh food to prevent spoilage.
• Model CLRCO2175 ice production after the first
harvest may take longer after the cleaning cycle
since restoring the refrigerator temperature will
take precedence over ice production. Once the
refrigerator reaches its set-point temperature, ice
making will resume.
since restoring the refrigerator temperature will
take precedence over ice production. Once the
refrigerator reaches its set-point temperature, ice
making will resume.
IMPORTANT
IMPORTANT
Never use anything to force ice from the
evaporator. Damage may result.
evaporator. Damage may result.
ULIN_0203_A
2
1