Directed Electronics PN 904100 产品宣传页

Compatible with the
following systems:

C

Co

on

nc

ce

ep

ptt  445500    ((G

G55))

S

So

olla

arriiss    ((G

G44))

M

Miilllle

en

niia

a    ((G

G44))

O

Om

mn

niiS

Stta

arrtt    G

G44))

A

Avva

an

nttg

gu

ua

arrd

d44    ((G

G44))

IIn

ntte

elllliiG

Gu

ua

arrd

d  99000000    ((G

G44))

IIn

ntte

elllliiG

Gu

ua

arrd

d  88000000    ((G

G44))

IIn

ntte

elllliiG

Gu

ua

arrd

d  77000000    ((G

G44))

IIn

ntte

elllliiG

Gu

ua

arrd

d  66000000    ((G

G44))

C

Cyyb

be

err44    ((G

G44))

C

Co

on

nc

ce

ep

ptt  660000    ((G

G44))

C

Co

on

nc

ce

ep

ptt  440000    ((G

G44))

C

Co

on

nc

ce

ep

ptt  220000    ((G

G44))

A

Ac

ce

e  77550000    ((G

G44))

A

Ac

ce

e  44000000    ((G

G44))

C

Co

on

nc

ce

ep

ptt  110000    ((G

G44))

M

Ma

attrriixx  22

M

Ma

attrriixx  33

M

Ma

attrriixx  R

RS

S22

M

Ma

attrriixx  R

RS

S33

44  B

Bu

utttto

on

n,,  C

Ca

arrb

bo

on

n  FFiib

be

err  A

AC

CG

G  rre

ep

plla

ac

ce

em

me

en

ntt  T

Trra

an

nssm

miitttte

err

PN 904100

MADE IN TAIWAN

© 2002 Directed Electronics, Inc. Vista CA 92083

All rights reserved.

P/N 904100     11/02

1. IGNITION ON: Place the key into the ignition and

turn to the ON position or start the engine.

2. ENTER PIN NUMBER: Enter your PIN number

using the Plainview 2 valet switch.

Note: The Factory default PIN number is 2 and can
be entered by pressing the 

button twice then the

"blank" button once of the Plainview 2 valet switch.

3. PRESS/HOLD/RELEASE: Immediately PRESS

and HOLD the 

button until you hear one chirp

and the Status LED turns on, then RELEASE the

button.

4. PRESS/RELEASE: PRESS and RELEASE the

"blank" button once. Pause until you hear one

chirp.

5. PRESS/RELEASE: PRESS and RELEASE the

button once. The siren will chirp once as you

push the button.

6. TRANSMIT: Press the 

button on you new

transmitter. The siren will chirp once to confirm it

has received the transmission.

7. TRANSMIT AGAIN: Press the 

button a

second time. The siren will chirp twice to confirm

it has learned your new transmitter.

8. IGNITION OFF: Turn the ignition off and remove

the key: The alarm will chirp three times to

indicate exiting transmitter learn routine.

9. TEST TRANSMITTER: Press the 

button

to verify that the transmitter is operating the

alarm system.

Note: This transmitter auto-learn routine is applicable
to specific system/ transmitter combinations, use
the following reference guide or consult your local
Clifford dealer for your particular application

904065 transmitter: Arrow 5 /Arrow 3 / Cyber 2 

904100 transmitter: Concept 100 / Concept 450/ 
Intelliguard 6000 / Cyber 4 

904075 transmitter: All other systems

This device complies with Part 15 of FCC rules.
Operation is subject to the following conditions: (1)
This device may not cause harmful interference, and
(2) This device must accept any interference
received, including interference that may cause
undesired operation. Changes or modifications not
expressly approved by the party responsible for
compliance could void the user's authority to
operate this device.

44  B

Bu

utttto

on

n,,  C

Ca

arrb

bo

on

n  FFiib

be

err  A

AC

CG

G  rre

ep

plla

ac

ce

em

me

en

ntt  T

Trra

an

nssm

miitttte

err  

PN 904100

TM