GE ESS25 用户手册

– 3 –

Installation

ATTENTION INSTALLER:

FOR A QUALITY INSTALLATION,
FOLLOW THESE INSTRUCTIONS.

• REMOVE AND DISCARD

SKIDBOARDS and bolts used to
hold skidboards.

• Use PADDED HAND TRUCK

to protect refrigerator finish.

• LEAVE TAPE ON DOORS until

refrigerator is in its final location.

• ADJUST FRONT ROLLERS

so that refrigerator is solid and
doors close easily.

• MAKE SURE DOORS ARE EVEN

AT TOP. Check gasket seal.

• SET BOTH CONTROLS TO “5”.

• SET ICEMAKER TO OFF until

water line is connected.

• IMPORTANT: IMMEDIATELY REMOVE ALL CLEAR PROTECTIVE TAPE FROM TRIM.
• TO REMOVE TAPE RESIDUE AND HANDPRINTS, USE APPLIANCE POLISH.
• REMOVE ALL TAPE AND OTHER PACKAGING MATERIAL FROM INSIDE REFRIGERATOR. DO NOT REMOVE SERIAL PLATE.

IMPORTANT: PLEASE READ CAREFULLY

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with a three-prong (grounding) plug that mates with a standard three-prong (grounding) wall receptacle to minimize the
risk of electric shock hazard from this appliance. The customer should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle
is properly grounded.

Where a standard two-prong wall receptacle is encountered, it is the personal responsibility and obligation of the customer to have it replaced with a properly grounded
three-prong wall receptacle.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.

USAGE SITUATIONS WHERE THE APPLIANCE’S POWER CORD WILL BE DISCONNECTED INFREQUENTLY
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug. However, if you still elect to use an adapter,
where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded two-prong wall receptacle by the use of a UL listed adapter which is
available at most hardware stores. The larger slot of the adapter must be aligned to provide proper polarity in the connection of the power cord.

CAUTION: Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal, and not insulated,
and the wall receptacle is grounded through the house wiring. The customer should have the circuit checked by a qualified electrician to make sure the receptacle is
properly grounded. When disconnecting the power cord from the adapter, always hold the adapter with one hand. If this is not done, the adapter ground terminal is very
likely to break with repeated use. Should this happen, DO NOT USE the appliance until a proper ground has again been established.

USAGE SITUATIONS WHERE THE APPLIANCE’S POWER CORD WILL BE DISCONNECTED FREQUENTLY
Do not use an adapter plug in these situations because frequent disconnecting of the power cord places undue strain on the adapter and leads to eventual failure of the
adapter ground terminal. The customer should have the two-prong wall receptacle replaced with a three-prong (grounding) receptacle by a qualified electrician before
using the appliance.

MAKE SURE PROPER
GROUND EXISTS
BEFORE USE

PREFERRED
METHOD

ENSURE PROPER
GROUND AND
FIRM CONNECTION
BEFORE USE

TEMPORARY METHOD
(Adapter plugs not
permitted in Canada)

197D3266P001

31-5087 9-00 JR

FRANÇAIS • ESP

ANOL

HEX-HEAD BOLTS (4)

ROLLERS

ÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

,,,,,

@@@@@

ÀÀÀÀÀ

ÀÀ

TRUCK FROM
SIDE ONLY

CARDBOARD
PROTECTS
DOOR EDGES

MAKE SURE FRONT
ROLLERS DO NOT
REST ON TRUCK

DO NOT
OVER-
TIGHTEN
STRAP

ROLLER
ADJUSTMENT

RAISE

9 IS COLDEST

0 IS OFF

FREEZER

FRESH FOOD

• At lower left hinge, remove tubing

from the clip.

• Disconnect the water line.

IF NECESSARY TO REMOVE DOORS, REMOVE ALL HINGES.
FOR DISPENSER MODELS:

COLLAR

PRESS THE WHITE COLLAR AS
YOU PULL OUT THE TUBING.

• Push tubing into connector

(

⁄

″

⁄

″

) to prevent leakage.

WHEN INSTALLING DOORS...

⁄

″

–

⁄

″

• At upper hinges, disconnect wiring connectors.

• Remove both hinges with each door to prevent

damage to tubing or wiring.

• Reinstall lower hinges and tighten hinge screws firmly.

• Place door on lower hinge pin and install upper hinges.

Tighten upper hinge screws firmly.

• Align both doors evenly at top by adjusting pin on lower

fresh food hinge.

• Reconnect wiring connectors and reinstall hinge covers.

• Reinstall tubing by pushing tubing into connector.

• Put tubing back into clip.

TO REINSTALL DOORS...

HINGE COVER

WIRING
CONNECTORS

TUBING CLIP

FRESH FOOD HINGE
ADJUSTMENT PIN

ALIGN DOORS EVENLY
AT TOP