ICOM IC-7000 用户手册

9

1

PANEL DESCRIPTION

zSPCH/LOCK KEY [SPCH/LOCK]

➥Push momentarily to have the frequency, etc. an-

nounced by the speech synthesizer. (p. 34)

• The parameters to be announced can be selected in

the miscellaneous (others) set mode. (p. 134)

➥Push and hold for 1 sec. to toggle the microphone

lock function ON and OFF. (p. 37)

xPTT SWITCH [PTT] (p. 37)

Push and hold to transmit; release to receive.

cUP/DOWN SWITCHES [Y]/[Z]

Change the operating frequency.

• Push and hold to change the frequency repeatedly.
• Tuning step size is 50 Hz if no TS indicator is displayed.

vTRANSMIT INDICATOR

Lights red while transmitting.

b KEYPAD

➥Pushing a key selects the operating band.

•

[(GENE)•] selects the general coverage band.

➥Pushing the same key 2 or 3 times calls up other

stacked frequencies in the band. (p. 28)

• Icom’s triple band stacking register memorizes 3 fre-

quencies in each band.

➥After pushing [(F-INP)ENT], enter a numeric fre-

quency, followed by pressing 

again. (p. 29)

• e.g. to enter 14.195 MHz, push 

[•] [1] [9] [5] [(F-INP)ENT].

nFILTER SELECTION [FIL] (p. 77)

➥Push momentarily to select one of three IF filter

settings.

➥Push and hold for 1 sec. to enter the filter set

mode.

mMODE KEY [MODE] (p. 34)

➥Push momentarily to cycle through the operating

modes:
USB/LSB

➧ CW/CW-R ➧

RTTY/RTTY-R

➧ AM/FM/WFM

➥Push and hold for 1 sec. to toggle the following

operating modes:
USB

↔ LSB

CW

↔ CW-R

RTTY

↔ RTTY-R

AM

→ FM

→ WFM

→ AM, etc

,POWER INDICATOR

Lights green while transceiver power is ON.

.PROGRAMMABLE FUNCTION KEYS [F-1]/[F-2]

Program and perform a selected function.

• The functions can be assigned in the miscellaneous (oth-

ers) set mode (p. 135). The default settings for 

[F-1] and

[F-2] are “MPW” and “MPR,” respectively.

⁄0MEMORY WRITE [MW] (pgs. 103, 104)

Push and hold for 1 sec. to store the displayed VFO
frequency and operating mode into the displayed
memory channel.

⁄1VFO/MEMORY SELECTION [V/M]

➥Push momentarily to toggle VFO and memory

modes. (pgs. 27, 102)

➥Push and hold for 1 sec. to transfer the selected

memory channel to the currently displayed VFO.
(p. 109)

⁄2TRANSMIT FREQUENCY CHECK [XFC] 

(pgs. 65, 91)

Monitors the transmit frequency when pushed and
held.

• While pushing this key, the transmit frequency can be

changed with 

[DIAL].

⁄3TUNER/CALL KEY [TUNER/CALL] 

➥During HF/50 MHz operation (p. 116):

●

● Push momentarily to toggle the automatic an-

tenna tuner function ON and OFF.

• An optional antenna tuner must be connected.
• “

” indicator appears when the tuner is ON.

●

● Push and hold for 2 sec. to manually tune the

antenna.

• An optional antenna tuner must be connected.
• “

” indicator appears when the tuner is ON.

➥During 144/430 MHz operation (p. 103):

Push momentarily to select the call channel (or
return to the previous channel/frequency when
the call channel is already selected).

• “C1” is the 144 MHz call channel and “C2” is the 430

MHz call channel.

■Microphone (HM-151)

[F-1] (MPW): Push to store the selected readout

frequency and operating mode into
a memo pad.

[F-2] (MPR): Push to call up a memo pad.

See the illustration of the HM-151 on page i-2.